Witam
Potrzebuję informacji jak mam skonfigurować Enterasysa S3 aby móc zestawić sesję BGP z 2 operatorami.
Mam 2x Enterasys S3 jest na nich zrobiony VRF
Na chwilę obecną mam 2 operatorów ale 1 op jest na 1 switchu 2 op na 2 switchu.
Chciałbym zapiąć 2 operatorów na 1 switchu.
Aktualna konfiguracja
# **** VRF INTERNET ****
set router vrf create INTERNET context INTERNET
router INTERNET
configure terminal
!
ip access-list extended INTERNET_IN
permit tcp any any established
exit
ip access-list standard LAN
permit 172.16.0.0 0.0.255.255
exit
!
route-map bgp OP1-IN permit 10
match prefix-list OP1-IN
set local-preference 150
exit
route-map bgp OP1-OUT permit 10
match prefix-list OP1-OUT
exit
!
interface vlan.0.11
description "VPN"
ip address IP_VRRP_1 255.255.255.224 primary
ip nat inside
vrrp create 1 v3-IPv4
vrrp address 1 IP_VRRP_Główny
vrrp priority 1 110
vrrp accept-mode 1
vrrp enable 1
no ip redirects
no shutdown
exit
interface vlan.0.21
description "OP1"
ip address ipOP1 255.255.255.252 primary
ip access-group INTERNET_IN in
ip nat outside
no shutdown
exit
!
# Static routes configured on routed interfaces
ip route MOJA SIEC/24 blackhole 1
!
!
router ospf 1
router-id IP_VRRP_1
network MOJA SIEC 0.0.0.255 area 0.0.0.0
redistribute bgp metric-type 2
log-adjacency
passive-interface vlan.0.21
passive-interface vlan.0.22
exit
!
router bgp XXYYZZ
bgp router-id IP_VRRP_1
aggregate-address MOJA SIEC/24 summary
log-up-down
neighbor ipOP1 remote-as XXYYZZ
neighbor ipOP1 route-map OP1-IN in
neighbor ipOP1 route-map OP1-OUT out
neighbor IP_VRRP_2 remote-as XXYYZZ
neighbor IP_VRRP_2 next-hop-self
network MOJA SIEC/24
exit
!
ip prefix-list OP1-IN seq 5 permit 0.0.0.0/0
ip prefix-list OP1-OUT seq 5 permit MOJA SIEC/24
ip nat pool OP1 ipOP1JA ipOP1JA
ip nat inside source list LAN pool OP1 overload
!
Potrzebuje podpowiedzi jak dodać do tej konfiguracji 2 operatora w taki sposób by aktualny operator był wiodącym a nowy backupowym.
Pozdrawiam
Marek
Enterasys S3 i BGP przy 2 ISP
wszystko inne - NIE licząc sprzętu typu SOHO!!!
Wiadomość
Autor
Przejdź do
- Technologia
- ↳ Routing
- ↳ Switching
- ↳ Security
- ↳ Voice
- ↳ Wireless
- ↳ Pozostałe
- ↳ Symulatory
- ↳ Hardware Cisco
- ↳ Problemy nie związane z technologiami
- Cloud and DC Infrastructure
- ↳ Data Center
- ↳ Hybrid/Public Cloud
- ↳ Software-defined networking (SDN)
- ↳ OpenStack and open infrastructure
- ↳ Automation, orchestration, scripting, programming
- Certyfikacja
- ↳ Poziom Associate
- ↳ Poziom Professional
- ↳ Poziom Expert
- ↳ Poziom Qualified
- ↳ CNAP (NetAcad), szkolenia i egzaminy
- ↳ Szkolenia i certyfikacje Public Cloud
- Platformy non-Cisco
- ↳ Juniper Networks
- ↳ Pozostałe
- Inne
- ↳ Njusy
- ↳ Hyde Park
- ↳ Kariera
- ↳ Bazar
- ↳ Kupię
- ↳ Sprzedam
- ↳ Linki
- Konferencje
- ↳ PLNOG / CONFIdence / DevOpsDays
- ↳ Confidence
- ↳ CiscoForum/CiscoExpo/CiscoSecure
- ↳ CCIE.PL Community Corner
- Archiwum
- ↳ Konkurs
- ↳ Regulaminy
- ↳ CCIE.pl FAQ
- Pozostałe