Niby działa, a niby nie...
Topologia wyglada tak:
Tylko to co ma zwiazek:
Kod: Zaznacz cały
R6# show run
ipv6 unicast-routing
interface GigabitEthernet0/0
no ip address
duplex auto
speed auto
ipv6 address FE80::9 link-local
ipv6 address 2001:DB8:ABCD:22::3/64
ipv6 ospf priority 30
ipv6 ospf 1 area 22
!
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
ipv6 address FE80::10 link-local
ipv6 address 2001:DB8:ABCD:1234::1/64
ipv6 rip RIPng-OSPFv3 enable
ipv6 router ospf 1
router-id 6.6.6.6
log-adjacency-changes
redistribute rip RIPng-OSPFv3 metric 99
redistribute connected metric 99
!
ipv6 router rip RIPng-OSPFv3
redistribute ospf 1 metric 16
redistribute connected metric 16
Kod: Zaznacz cały
R6#show ipv6 ospf interface
GigabitEthernet0/0 is up, line protocol is up
Link Local Address FE80::9, Interface ID 1
Area 22, Process ID 1, Instance ID 0, Router ID 6.6.6.6
Network Type BROADCAST, Cost: 1
Transmit Delay is 1 sec, State BDR, Priority 30
Designated Router (ID) 3.3.3.3, local address FE80::9
Backup Designated Router (ID) 6.6.6.6, local address FE80::9
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
Hello due in 00:00:05
Index 1/1, flood queue length 0
Next 0x0(0)/0x0(0)
Last flood scan length is 1, maximum is 1
Last flood scan time is 0 msec, maximum is 0 msec
Neighbor Count is 2, Adjacent neighbor count is 2
Adjacent with neighbor 3.3.3.3 (Designated Router)
Adjacent with neighbor 5.5.5.5
Suppress hello for 0 neighbor(s)
Kod: Zaznacz cały
R6#show ipv6 rip database
RIP process "RIPng-OSPFv3" local RIB
2001:DB8:ABCD:1234::/64, metric 2
GigabitEthernet0/1/FE80::11, expires in 176 sec
2001:DB8:ABCD:12AB::/64, metric 2, installed
GigabitEthernet0/1/FE80::11, expires in 176 sec
Kod: Zaznacz cały
R5#show ipv6 route
IPv6 Routing Table - 8 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route, M - MIPv6
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
D - EIGRP, EX - EIGRP external
OI 2001:DB8:ABCD::/64 [110/2]
via FE80::7, GigabitEthernet0/0
OI 2001:DB8:ABCD:15::/64 [110/3]
via FE80::7, GigabitEthernet0/0
C 2001:DB8:ABCD:22::/64 [0/0]
via GigabitEthernet0/0, directly connected
L 2001:DB8:ABCD:22::1/128 [0/0]
via GigabitEthernet0/0, receive
OI 2001:DB8:ABCD:15A::/64 [110/4]
via FE80::7, GigabitEthernet0/0
OE2 2001:DB8:ABCD:1234::/64 [110/99]
via FE80::9, GigabitEthernet0/0
OE2 2001:DB8:ABCD:12AB::/64 [110/20]
via FE80::9, GigabitEthernet0/0
L FF00::/8 [0/0]
via Null0, receive
Wpisy dotyczace redystrybucji na R6
Kod: Zaznacz cały
R6#show ipv6 protocols
IPv6 Routing Protocol is "connected"
IPv6 Routing Protocol is "ND"
IPv6 Routing Protocol is "rip RIPng-OSPFv3"
Interfaces:
GigabitEthernet0/1
Redistribution:
connected with metric 16
IPv6 Routing Protocol is "ospf 1"
Interfaces (Area 22)
GigabitEthernet0/0
Redistribution:
Redistributing protocol rip with metric 99
Redistributing protocol connected with metric 99
Kod: Zaznacz cały
R5#ping 2001:db8:abcd:1234::1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2001:db8:abcd:1234::1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5),round-trip min/avg/max = 0/0/0 ms
R5#ping 2001:db8:abcd:1234::2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2001:db8:abcd:1234::2, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
A teraz R7 (brak pisow OSPFv3)
Kod: Zaznacz cały
R7#show ipv6 route
IPv6 Routing Table - 5 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route, M - MIPv6
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
D - EIGRP, EX - EIGRP external
C 2001:DB8:ABCD:1234::/64 [0/0]
via GigabitEthernet0/0, directly connected
L 2001:DB8:ABCD:1234::2/128 [0/0]
via GigabitEthernet0/0, receive
C 2001:DB8:ABCD:12AB::/64 [0/0]
via GigabitEthernet0/1, directly connected
L 2001:DB8:ABCD:12AB::1/128 [0/0]
via GigabitEthernet0/1, receive
L FF00::/8 [0/0]
via Null0, receive
Wydaje mi sie ze redystrybucja RIPng na obszary OSPFv3 przebiegla pomyslnie, ale nie tak dobrze juz dla RIPng, bo nie widac informacji na R7 dotyczacych OSPFv3. Nie bardzo wiem "dlaczego".
Mam nadzieje, ze podalem najwazniejsze informacje, ktore pomoga przeanalizowac sytuacje. Nie mam pomyslu