3G na 881G K9

Problemy związane z routingiem
Wiadomość
Autor
Awatar użytkownika
miroxpl
fresh
fresh
Posty: 8
Rejestracja: 02 gru 2016, 13:44

3G na 881G K9

#1

#1 Post autor: miroxpl »

Witam serdecznie,

Posiadam kartę SIM T-Mobile, aktywną bez pinu, w telefonie działa z niej internet od razu. Natomiast mam problem z uruchomieniem na routerze CISCO 881G-K9, próbowałem już kilku sposobów konfiguracji, zakładałem różne profile dla cellurar, kombinowałem z dialerem, ale pomysły już mi się skończyły jak ten temat ugryźć. Może będzie mogli mi pomóc?
Przesyłam aktualną konfigurację routera, aczkolwiek było ich kilka, cały czas jest cellular inactive

Kod: Zaznacz cały

Router10#show running-config
Building configuration...

Current configuration : 2551 bytes
!
! Last configuration change at 13:14:10 UTC Fri Dec 2 2016
!
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router10
!
boot-start-marker
warm-reboot
boot-end-marker
!

!
no aaa new-model
!
memory-size iomem 10
!
!
ip source-route
!
!
ip dhcp excluded-address 10.1.98.1 10.1.98.100
ip dhcp excluded-address 192.168.1.0 192.168.1.99
!
ip dhcp pool WIFI
   network 10.1.98.0 255.255.255.0
   default-router 10.1.98.1
   dns-server 8.8.8.8
!
!
ip cef
no ip domain lookup
no ipv6 cef
!
!
multilink bundle-name authenticated
chat-script ERA "" "AT!SCACT=1,1" TIMEOUT 60 "OK"
chat-script gsm "" "atdt*99#" TIMEOUT 60 "CONNECT"
license udi pid CISCO881G-K9 sn 
!

!
!
!
!
controller Cellular 0
!
!
!
!
!
!
!
!
interface Loopback0
 no ip address
!
interface FastEthernet0
 switchport access vlan 20
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
 ip address 192.168.1.10 255.255.255.0
 shutdown
 duplex auto
 speed auto
 standby 0 ip 192.168.1.1
 standby 0 priority 140
 standby 0 preempt
!
interface Cellular0
 ip address negotiated
 ip virtual-reassembly
 encapsulation ppp
 load-interval 60
 dialer in-band
 dialer idle-timeout 0
 dialer-group 1
 async mode interactive
 ppp chap refuse
!
interface Vlan1
 no ip address
!
interface Vlan10
 ip address 192.168.10.10 255.255.255.0
!
interface Vlan20
 ip address 10.1.98.1 255.255.255.0
!
interface Dialer0
 ip address negotiated
 encapsulation ppp
 dialer pool 1
 dialer idle-timeout 0
 dialer string hspa
 ppp authentication chap pap
!
interface Dialer1
 ip address negotiated
 ip virtual-reassembly
 encapsulation ppp
 dialer pool 1
 dialer idle-timeout 0
 dialer string internet
 dialer persistent
 dialer-group 1
 no cdp enable
!
router ospf 1
 log-adjacency-changes
 network 10.1.98.0 0.0.0.255 area 0
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
ip route 0.0.0.0 0.0.0.0 Cellular0
!
dialer-list 2 protocol ip permit
!
!
!
!
!
control-plane
!
!
line con 0
 password ala ma kota
 login local
 no modem enable
line aux 0
line 3
 exec-timeout 0 0
 script dialer gsm
 modem InOut
 no exec
 transport input all
 rxspeed 7200000
 txspeed 5760000
line vty 0
 login local
 transport input all
line vty 1 4
 password alamakota
 login local
 transport input telnet
!
end

Kod: Zaznacz cały

Router10#show cellular 0 all
Hardware Information
====================

Profile Information
====================
Profile 1 = INACTIVE*
--------
PDP Type = PPP
Access Point Name (APN) = internet
Authentication = None
Username: , Password:

Profile 2 = INACTIVE
--------
PDP Type = PPP
Access Point Name (APN) = no
Authentication = PAP
Username: internet, Password: no

Profile 3 = INACTIVE
--------
PDP Type = IPv4
Access Point Name (APN) =
Authentication = None
Username: , Password:

 * - Default profile

Data Connection Information
===========================
Data Transmitted = 0 bytes, Received = 0 bytes
Profile 1, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 2, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 3, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 4, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 5, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 6, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 7, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 8, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 9, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 10, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 11, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 12, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 13, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 14, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 15, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 16, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state

Network Information
===================
Current Service Status = Normal, Service Error = None
Current Service = Combined
Packet Service = HSPA (Attached)
Packet Session Status = Inactive
Current Roaming Status = Home
Network Selection Mode = Automatic
Country = POL, Network = Era
Mobile Country Code (MCC) = 260
Mobile Network Code (MNC) = 2
Location Area Code (LAC) = 57410
Routing Area Code (RAC) = 35
Cell ID = 21195
Primary Scrambling Code = 73
PLMN Selection = Automatic
Registered PLMN =  , Abbreviated =
Service Provider = T-Mobile.pl

Radio Information
=================
Radio power mode = ON
Current Band = WCDMA 2100, Channel Number = 10688
Current RSSI = -94 dBm
Band Selected = Auto
Number of nearby cells = 1
Cell 1
        Primary Scrambling Code = 0x49
        RSCP = -94 dBm, ECIO = -3 dBm


Modem Security Information
==========================
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of Retries remaining = 3

Awatar użytkownika
toczyskik
wannabe
wannabe
Posty: 312
Rejestracja: 09 maja 2006, 14:28
Lokalizacja: Warszawa

Re: 3G na 881G K9

#2

#2 Post autor: toczyskik »

miroxpl pisze:Witam serdecznie,

Posiadam kartę SIM T-Mobile, aktywną bez pinu, w telefonie działa z niej internet od razu. Natomiast mam problem z uruchomieniem na routerze CISCO 881G-K9, próbowałem już kilku sposobów konfiguracji, zakładałem różne profile dla cellurar, kombinowałem z dialerem, ale pomysły już mi się skończyły jak ten temat ugryźć. Może będzie mogli mi pomóc?
Przesyłam aktualną konfigurację routera, aczkolwiek było ich kilka, cały czas jest cellular inactive
Hej,

Upewnij się, że Twoja karta jest na 3G, a nie LTE bo wtedy jest inna konfiguracja. Kolejna sprawa, to najpierw konfiguruj interfejs Dialer, a później Cellular. Nie chciało mi się dochodzić czy to w takiej kolejności ma być, czy to jakiś błąd w sofcie jest.

Mi też pomogło usunięcie z interfejsu Cell tego:

Kod: Zaznacz cały

dialer in-band
dialer pool-member 1
a później wprowadzenie tego od nowa.

Tu masz moją konfigurację, która testowałem parę dni temu która działała.

Kod: Zaznacz cały

!
! Last configuration change at 11:37:51 UTC Tue Nov 15 2016
!
version 15.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
!
!
!
!
!
!         
!
!
!
!


!
!
!
!
ip cef
no ipv6 cef
!
!
!
!
!
multilink bundle-name authenticated
!
!
chat-script gsm "" "ATDT*99***1#" TIMEOUT 60 "CONNECT"
!         
!
!
!
!
!
cts logging verbose
license udi pid C899G-LTE-GA-K9 sn FCZ123456
!
!
!
!
!
!
!
controller Cellular 0
 lte modem link-recovery rssi onset-threshold -110
 lte modem link-recovery monitor-timer 20
 lte modem link-recovery wait-timer 10
 lte modem link-recovery debounce-count 6
!
! 
!
!         
!
!
!
!
!
!
!
!
interface Cellular0
 no ip address
 encapsulation slip
 dialer in-band
 dialer pool-member 1
!
interface FastEthernet0
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface GigabitEthernet0
 no ip address
!         
interface GigabitEthernet1
 no ip address
!
interface GigabitEthernet2
 no ip address
!
interface GigabitEthernet3
 no ip address
!
interface GigabitEthernet4
 no ip address
!
interface GigabitEthernet5
 no ip address
!
interface GigabitEthernet6
 no ip address
!
interface GigabitEthernet7
 no ip address
!
interface GigabitEthernet8
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface GigabitEthernet9
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface Vlan1
 no ip address
!
interface Dialer1
 ip address negotiated
 encapsulation ppp
 dialer pool 1
 dialer idle-timeout 0
 dialer string gsm
 dialer persistent
 ppp ipcp dns request
 no cdp enable
!         
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
ip route 0.0.0.0 0.0.0.0 Dialer1
!
!
!
control-plane
!
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
!
!
!
!         
!
!
line con 0
 script dialer gsm
 logging synchronous
 no modem enable
line aux 0
line 2
 no activation-character
 no exec
 transport preferred none
 transport input all
 stopbits 1
line 3
 no exec
 speed 384000
line vty 0 4
 login
 transport input none
!
scheduler allocate 20000 1000
!         
!
!
end
Pozdrawiam
Krzysiek Te.

Awatar użytkownika
miroxpl
fresh
fresh
Posty: 8
Rejestracja: 02 gru 2016, 13:44

Re: 3G na 881G K9

#3

#3 Post autor: miroxpl »

już jestem bliżej niż dalej...

Debug wywala:

Kod: Zaznacz cały

*Dec  6 10:10:55.343: [Cellular0]:MGMT RX (RSCP_ECIO) (24 bytes):
 00 14 6B 29 70 0B 07 00 00 00 00 00 00 0A 00 01
 00 01 00 49 00 61 00 0A


Router#
*Dec  6 10:10:56.459: [Cellular0]:MGMT RX (HEARTBEAT) (14 bytes):
 00 0A 6B 2A 00 00 07 00 00 00 00 00 00 00


Router#
*Dec  6 10:10:58.347: [Cellular0]:MGMT RX (RSCP_ECIO) (24 bytes):
 00 14 6B 2B 70 0B 07 00 00 00 00 00 00 0A 00 01
 00 01 00 49 00 5F 00 07


Router#
*Dec  6 10:11:01.347: [Cellular0]:MGMT RX (RSCP_ECIO) (24 bytes):
 00 14 6B 2C 70 0B 07 00 00 00 00 00 00 0A 00 01
 00 01 00 49 00 60 00 08


Router#
*Dec  6 10:11:03.459: [Cellular0]:MGMT RX (HEARTBEAT) (14 bytes):
 00 0A 6B 2D 00 00 07 00 00 00 00 00 00 00


*Dec  6 10:11:04.351: [Cellular0]:MGMT RX (RSCP_ECIO) (24 bytes):
 00 14 6B 2E 70 0B 07 00 00 00 00 00 00 0A 00 01
 00 01 00 49 00 5F 00 07

Debug odpaliłem dla Cellular 0 i Dialer 1, jakby był tyko problem z konfiguracją profilu cell0?

zrobiłem: cell0 gsm prof create 1 internet ppp
Jak zaleca operator:
Konto: T-Mobile
Numer dostępowy: *99#
Hasło: puste
APN: internet
Nazwa użytkownika: puste
Protokół: CHAP


sh run

Kod: Zaznacz cały

Current configuration : 1441 bytes
!
! Last configuration change at 09:45:39 UTC Tue Dec 6 2016
!
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
warm-reboot
boot-end-marker
!
!
no aaa new-model
!
memory-size iomem 10
!
!

ip source-route
!
!
!
!
ip cef
no ipv6 cef
!
!
multilink bundle-name authenticated
chat-script gsm "" "ATDT*99***1#" TIMEOUT 60 "CONNECT"
license udi pid CISCO881G-K9 sn 
!
!
!
!
!
!
controller Cellular 0

!
!
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface Cellular0
 no ip address
 ip virtual-reassembly
 encapsulation ppp
 dialer in-band
 dialer pool-member 1
!
interface Vlan1
 ip address 10.1.98.1 255.255.255.0
!
interface Dialer1
 ip address negotiated
 encapsulation ppp
 dialer pool 10
 dialer idle-timeout 0
 dialer string gsm
 ppp ipcp dns request
 no cdp enable
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
ip route 0.0.0.0 0.0.0.0 Dialer1
!
!
!
!
!
!
control-plane
!
!
line con 0
 script dialer gsm
 logging synchronous
 no modem enable
line aux 0
line 3
 exec-timeout 0 0
 script dialer gsm
 login
 modem InOut
 no exec
 transport input all
 rxspeed 7200000
 txspeed 5760000
line vty 0 4
 login
 transport input all
!
end

lbromirs
CCIE
CCIE
Posty: 4101
Rejestracja: 30 lis 2006, 08:44

Re: 3G na 881G K9

#4

#4 Post autor: lbromirs »

Pokaż 'sh dialer' i jeśli coś jest nie tak z uwierzytelnieniem - zajmij się 'debug ppp authentication'.

Awatar użytkownika
miroxpl
fresh
fresh
Posty: 8
Rejestracja: 02 gru 2016, 13:44

Re: 3G na 881G K9

#5

#5 Post autor: miroxpl »

Wklejam aktualny sh dialer, debug ppp nic nie pokazuje

Kod: Zaznacz cały

Router#show dialer


Ce0 - dialer type = IN-BAND ASYNC NO-PARITY
Dialer pool 1, priority 0
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle


Di1 - dialer type = DIALER PROFILE
Idle timer (never), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
Number of active calls = 0


Dial String      Successes   Failures    Last DNIS   Last status
gsm                      0          0    never                   -   Default



lbromirs
CCIE
CCIE
Posty: 4101
Rejestracja: 30 lis 2006, 08:44

Re: 3G na 881G K9

#6

#6 Post autor: lbromirs »

miroxpl pisze:Wklejam aktualny sh dialer, debug ppp nic nie pokazuje

Kod: Zaznacz cały

Router#show dialer


Ce0 - dialer type = IN-BAND ASYNC NO-PARITY
Dialer pool 1, priority 0
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle


Di1 - dialer type = DIALER PROFILE
Idle timer (never), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
Number of active calls = 0


Dial String      Successes   Failures    Last DNIS   Last status
gsm                      0          0    never                   -   Default


Nie próbujesz w ogóle dzwonić, to nie pokazuje :) Dodaj do swojej konfiguracji 'dialer-list 10 protocol ip permit' i spróbuj popingać cokolwiek w internecie.

Polecam ten dokument.

Awatar użytkownika
miroxpl
fresh
fresh
Posty: 8
Rejestracja: 02 gru 2016, 13:44

Re: 3G na 881G K9

#7

#7 Post autor: miroxpl »

Walczę dzielnie, uparcie z tym i dało mi się wywalczyć już dialer w stanie call, dzwoni lecz dodzwonić się nigdzie nie może, starałem się skonfigurować według tego linku od Ibromirs, teraz wygląda to następująco:

Kod: Zaznacz cały

Router#show dialer


Ce0 - dialer type = IN-BAND ASYNC NO-PARITY
Dialer pool 1, priority 0
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is call pending
Dial reason: ip (s=10.1.98.55, d=8.8.8.8)


Di1 - dialer type = DIALER PROFILE
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is call pending
Number of active calls = 0


Dial String      Successes   Failures    Last DNIS   Last status
8134                     0          3    00:00:44           failed   Default
Router#
*Dec  6 17:00:57.433: CHAT3: Timeout expecting: CONNECT
*Dec  6 17:00:57.433: CHAT3: Chat script gsm finished, status = Connection timed out; remote host not responding
*Dec  6 17:00:57.433: Ce0 DDR: disconnecting call
Router#ping 8.8.8.8


Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:


*Dec  6 17:01:08.653: Di1 DDR: ip (s=10.1.98.1, d=8.8.8.8), 100 bytes, outgoing interesting (ip PERMIT)
*Dec  6 17:01:08.653: Di1: No free dialer - starting fast idle timer.
*Dec  6 17:01:10.653: Di1 DDR: ip (s=10.1.98.1, d=8.8.8.8), 100 bytes, outgoing interesting (ip PERMIT)
*Dec  6 17:01:10.653: Di1: No free dialer - starting fast idle timer.
*Dec  6 17:01:12.433: Ce0 DDR: re-enable timeout
*Dec  6 17:01:12.653: Di1 DDR: ip (s=10.1.98.1, d=8.8.8.8), 100 bytes, outgoing interesting (ip PERMIT)
*Dec  6 17:01:12.653: Ce0 DDR: rotor dialout [best] least recent failure is also most recent failure
*Dec  6 17:01:12.653: Ce0 DDR: rotor dialout [best] also has most recent failure
*Dec  6 17:01:12.653: Ce0 DDR: rotor dialout [best]
*Dec  6 17:01:12.653: Ce0 DDR: Dialing cause ip (s=10.1.98.1, d=8.8.8.8)
*Dec  6 17:01:12.653: Ce0 DDR: Attempting to dial gsm
*Dec  6 17:01:12.653: CHAT3: Attempting async line dialer script
*Dec  6 17:01:12.653: CHAT3: Dialing using Modem script: gsm & System script: none
*Dec  6 17:01:12.653: CHAT3: process started
*Dec  6 17:01:12.653: CHAT3: Asserting DTR
*Dec  6 17:01:12.657: CHAT3: Chat script gsm started
*Dec  6 17:01:12.657: CHAT3: Sending string: ATDT*99***1#
*Dec  6 17:01:12.657: CHAT3: Expecting string: CONNECT.
*Dec  6 17:01:14.653: Di1 DDR: ip (s=10.1.98.1, d=8.8.8.8), 100 bytes, outgoing interesting (ip PERMIT).
*Dec  6 17:01:16.653: Di1 DDR: ip (s=10.1.98.1, d=8.8.8.8), 100 bytes, outgoing interesting (ip PERMIT).
Success rate is 0 percent (0/5)
Router#
i według tego wsparcia cisco teraz powinienem skonfigurować interfejs BRI0, ale ten router 881G nie posiada takiego...

Kod: Zaznacz cały

 Example 3

    *Mar  1 00:25:32.551: Di1 DDR: ip (s=10.1.0.1, d=192.168.201.1), 
           100 bytes, outgoing interesting (ip PERMIT)
         *Mar  1 00:25:32.555: Di1 DDR: No free dialer - starting fast idle timer.

In this case, the outgoing packet is to be considered interesting enough to bring up the link, but there is no physical interface available to place the call. Make sure that dialer pool-member number is configured in the physical interface and dialer pool number is configured in the Dialer interface. Example:

    interface BRI0
          dialer pool-member 1
         !
         interface Dialer1
          dialer pool 1

Also, verify that the physical interface is not in shutdown state. Use the no shutdown command on the physical interface. 
Ostatnio zmieniony 06 gru 2016, 18:10 przez miroxpl, łącznie zmieniany 1 raz.

Awatar użytkownika
konradrz
CCIE
CCIE
Posty: 400
Rejestracja: 23 sty 2008, 14:21
Lokalizacja: Singapore, SG
Kontakt:

Re: 3G na 881G K9

#8

#8 Post autor: konradrz »

miroxpl pisze:

Kod: Zaznacz cały

*Dec  6 17:01:12.657: CHAT3: Sending string: ATDT*99***1#
Ja to stary i ślepy jestem, ale nie miałeś przypadkiem słać "ATDT*99#"? (nie sądzę żeby to jakąś wielką różnicę czyniło, aaaale)
W oryginalnym poście miałeś właśnie ATDT*99# (jako "script gsm"), ale się do niego nie odwoływałeś (miałeś "dialer string hspa")
Na pewno SIM masz 3g, nie LTE czy co inszego?

Awatar użytkownika
lxs
wannabe
wannabe
Posty: 177
Rejestracja: 08 sty 2014, 16:27
Lokalizacja: 52.182098, 21.005445

Re: 3G na 881G K9

#9

#9 Post autor: lxs »

ATDT*99***1# wybiera profil numer 1. Nie powinno mieć to znaczenia dla działania.

Nie masz interfejsu BRI0 bo to nie jest modem ISDN tylko 3G. Zamiast BRI0 masz Cellular0.

Jak możesz to wrzuć output:

Kod: Zaznacz cały

show cellular 0 all
debug modem
debup chat
debug ppp negotiation
debug ppp event
debup ppp error
Mi osobiście brakuje w Twojej konfiguracji tego "asynchronous mode interactive" w Cellular 0 i uwierzytelnienia.

Awatar użytkownika
miroxpl
fresh
fresh
Posty: 8
Rejestracja: 02 gru 2016, 13:44

Re: 3G na 881G K9

#10

#10 Post autor: miroxpl »

Debugi nic nie pokazują, ale show cell0 już tak, z tego co widzę przyczyna to chyba jednak zła karta SIM, czy nie mam racji?

Current Service Status = Normal, Service Error = Service option not supported

Kod: Zaznacz cały

Router#debug mod
Router#debug modem
Modem control/process activation debugging is on
Router#debu
Router#debug ch
Router#debug chat
Chat scripts activity debugging is on
Router#deb
*Dec  8 11:43:31.899: TTY0: resume timer type 1 (OK)
Router#deb
Router#debug ppp ne
Router#debug ppp negotiation
PPP protocol negotiation debugging is on
Router#deb
*Dec  8 11:43:37.987: TTY0: resume timer type 1 (OK)
Router#deb
Router#debug ppp ev
Router#debug ppp ev
Router#debug ppp eve
Router#debug ppp ?
  authentication  CHAP/PAP/MSCHAP/EAP authentication
  authorization   PP authorization
  bap             BAP protocol transactions
  cbcp            Callback Control Protocol negotiation
  elog            PPP ELOGs
  error           Protocol errors and error statistics
  mppe            MPPE Events
  multilink       Multilink activity
  negotiation     Protocol parameter negotiation
  packet          Low-level PPP packet dump
  subscriber      PPP interactions with Subscriber Service Switch and
                  forwarding

Router#debug ppp err
Router#debug ppp error
PPP protocol errors debugging is on
Router#
*Dec  8 11:44:01.847: TTY0: resume timer type 1 (OK)
Router#show cell
Router#show cellular 0 al
Router#show cellular 0 all


Profile Information
====================
Profile 1 = INACTIVE*
--------
PDP Type = PPP
Access Point Name (APN) = internet
Authentication = None
Username: , Password:
 --More--
*Dec  8 11:44:19.731: TTY0: resume timer type 1 (OK)

Profile 2 = INACTIVE
--------
PDP Type = PPP
Access Point Name (APN) = no
Authentication = PAP
Username: internet, Password: no

Profile 3 = INACTIVE
--------
PDP Type = IPv4
Access Point Name (APN) =
Authentication = None
Username: , Password:

 * - Default profile

Data Connection Information
===========================
Data Transmitted = 0 bytes, Received = 0 bytes
Profile 1, Packet Session Status = INACTIVE
        Inactivity Reason = Service option not supported
Profile 2, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 3, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 4, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 5, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 6, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 7, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 8, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 9, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 10, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 11, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 12, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 13, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 14, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 15, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 16, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state

Network Information
===================
Current Service Status = Normal, Service Error = Service option not supported
Current Service = Combined
Packet Service = HSPA (Attached)
Packet Session Status = Inactive
Current Roaming Status = Home
Network Selection Mode = Automatic
Country = POL, Network = Era
Mobile Country Code (MCC) = 260
Mobile Network Code (MNC) = 2
Location Area Code (LAC) = 57410
Routing Area Code (RAC) = 35
Cell ID = 21185
Primary Scrambling Code = 73
PLMN Selection = Automatic
Registered PLMN =  , Abbreviated =
Service Provider = T-Mobile.pl

Radio Information
=================
Radio power mode = ON
Current Band = WCDMA 2100, Channel Number = 10663
Current RSSI = -94 dBm
Band Selected = Auto
Number of nearby cells = 1
Cell 1
        Primary Scrambling Code = 0x49
        RSCP = -94 dBm, ECIO = -4 dBm


Modem Security Information
==========================
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of Retries remaining = 3
Router#

lbromirs
CCIE
CCIE
Posty: 4101
Rejestracja: 30 lis 2006, 08:44

Re: 3G na 881G K9

#11

#11 Post autor: lbromirs »

Masz bardzo słaby sygnał. Bardzo. Nie jestem pewien czy w ogóle uda Ci się sensownie i stabilnie
podnieść warstwę IP.

Karta jest aktywowana? Nie wybrał sobie automatycznie PLMNa, co może
oznaczać, że po prostu nie chce wpuścić Cię do sieci.

Awatar użytkownika
lxs
wannabe
wannabe
Posty: 177
Rejestracja: 08 sty 2014, 16:27
Lokalizacja: 52.182098, 21.005445

Re: 3G na 881G K9

#12

#12 Post autor: lxs »

Wsadź w ten router inną kartę SIM i zobacz czy polecenie
"show cellular 0 all " wskaże "Registered PLMN = , Abbreviated =" coś innego niż puste miejsce. Wedlug logów z poprzednich postów twoja antena dostaje wyłącznie sygnały RSCP_ECIO i Heartbeaty, co jedynie może świadczyć, że antena działa. Karta SIM nie rejestruje się do sieci. Poniżej -90 dBm to raczej nic nie działa.
Druga rzecz, to sprawdź czy nie masz modemu PCEX-3G-HSPA-US, tylko PCEX-3G-HSPA-G. Różnica jest taka, że WCDMA w US i w Europie działają inaczej.

ODPOWIEDZ