Kod: Zaznacz cały
Booting system, please wait...
CISCO SYSTEMS
Embedded BIOS Version 1.0(11)5 08/28/08 15:11:51.82
Low Memory: 631 KB
High Memory: 1024 MB
PCI Device Table.
Bus Dev Func VendID DevID Class Irq
00 00 00 8086 2578 Host Bridge
00 01 00 8086 2579 PCI-to-PCI Bridge
00 03 00 8086 257B PCI-to-PCI Bridge
00 1C 00 8086 25AE PCI-to-PCI Bridge
00 1D 00 8086 25A9 Serial Bus 11
00 1D 01 8086 25AA Serial Bus 10
00 1D 04 8086 25AB System
00 1D 05 8086 25AC IRQ Controller
00 1D 07 8086 25AD Serial Bus 9
00 1E 00 8086 244E PCI-to-PCI Bridge
00 1F 00 8086 25A1 ISA Bridge
00 1F 02 8086 25A3 IDE Controller 11
00 1F 03 8086 25A4 Serial Bus 5
00 1F 05 8086 25A6 Audio 5
02 01 00 8086 1075 Ethernet 11
03 01 00 177D 0003 Encrypt/Decrypt 9
03 02 00 8086 1079 Ethernet 9
03 02 01 8086 1079 Ethernet 9
03 03 00 8086 1079 Ethernet 9
03 03 01 8086 1079 Ethernet 9
04 02 00 8086 1209 Ethernet 11
04 03 00 8086 1209 Ethernet 5
Evaluating BIOS Options ...
Launch BIOS Extension to setup ROMMON
Cisco Systems ROMMON Version (1.0(11)5) #0: Thu Aug 28 15:23:50 PDT 2008
Platform ASA5510
Use BREAK or ESC to interrupt boot.
Use SPACE to begin boot immediately.
Launching BootLoader...
Boot configuration file contains 3 entries.
Loading disk0:/asa844-3-k8.bin... Booting...
Platform ASA5510
Loading...
IO memory blocks requested from bigphys 32bit: 13008
Po kilku takich nieudanych próbach stwierdziłem że spróbuję wgrać obraz na nowo w rommon, jednak wszystko kończy się tak samo:
Kod: Zaznacz cały
Booting system, please wait...
CISCO SYSTEMS
Embedded BIOS Version 1.0(11)5 08/28/08 15:11:51.82
Low Memory: 631 KB
High Memory: 1024 MB
PCI Device Table.
Bus Dev Func VendID DevID Class Irq
00 00 00 8086 2578 Host Bridge
00 01 00 8086 2579 PCI-to-PCI Bridge
00 03 00 8086 257B PCI-to-PCI Bridge
00 1C 00 8086 25AE PCI-to-PCI Bridge
00 1D 00 8086 25A9 Serial Bus 11
00 1D 01 8086 25AA Serial Bus 10
00 1D 04 8086 25AB System
00 1D 05 8086 25AC IRQ Controller
00 1D 07 8086 25AD Serial Bus 9
00 1E 00 8086 244E PCI-to-PCI Bridge
00 1F 00 8086 25A1 ISA Bridge
00 1F 02 8086 25A3 IDE Controller 11
00 1F 03 8086 25A4 Serial Bus 5
00 1F 05 8086 25A6 Audio 5
02 01 00 8086 1075 Ethernet 11
03 01 00 177D 0003 Encrypt/Decrypt 9
03 02 00 8086 1079 Ethernet 9
03 02 01 8086 1079 Ethernet 9
03 03 00 8086 1079 Ethernet 9
03 03 01 8086 1079 Ethernet 9
04 02 00 8086 1209 Ethernet 11
04 03 00 8086 1209 Ethernet 5
Evaluating BIOS Options ...
Launch BIOS Extension to setup ROMMON
Cisco Systems ROMMON Version (1.0(11)5) #0: Thu Aug 28 15:23:50 PDT 2008
Platform ASA5510
Use BREAK or ESC to interrupt boot.
Use SPACE to begin boot immediately.
Boot interrupted.
Management0/0
Ethernet auto negotiation timed out.
Interface-4 Link Not Established (check cable).
Default Interface number-4 Not Up
Use ? for help.
rommon #0> ADDRESS=10.0.0.2
rommon #1> SERVER=10.0.0.1
rommon #2> IMAGE=asa847-k8.bin
rommon #3> PORT=Ethernet0/0
Ethernet0/0
Link is UP
MAC Address: 70ca.9ba0.57b0
rommon #4> ping server
Sending 20, 100-byte ICMP Echoes to server 10.0.0.1, timeout is 4 seconds:
??!!!!!!!!!!!!!!!!!!
Success rate is 90 percent (18/20)
rommon #5> tftp
ROMMON Variable Settings:
ADDRESS=10.0.0.2
SERVER=10.0.0.1
GATEWAY=0.0.0.0
PORT=Ethernet0/0
VLAN=untagged
IMAGE=asa847-k8.bin
CONFIG=disk0:/last_config
LINKTIMEOUT=20
PKTTIMEOUT=4
RETRY=20
tftp asa847-k8.bin@10.0.0.1
!!!
Received 24809472 bytes
Launching TFTP Image...
Cisco Security Appliance admin loader (3.0) #0: Fri Aug 30 19:48:50 PDT 2013
Platform ASA5510
Loading...
IO memory blocks requested from bigphys 32bit: 13008
Czy ma ktoś jakieś podejrzenia/wskazówki co mogło się stać i jak to rozwiązać?