CUCME TRANSCODING FEIL

Wiadomość

Sagittarius · #1

Witam, Mam taki problem.

CME_Voice#sh sccp
SCCP Admin State: UP
Gateway Local Interface: FastEthernet0/1.10
        IPv4 Address: 192.168.1.1
        Port Number: 2000
IP Precedence: 3
User Masked Codec list: None
Call Manager: 192.168.1.1, Port Number: 2000
                Priority: N/A, Version: 7.0, Identifier: 1
                Trustpoint: N/A

Transcoding Oper State: ACTIVE_IN_PROGRESS - Cause Code: CCM_REGISTER_FAILED
Active Call Manager: 192.168.1.1, Port Number: 2000
TCP Link Status: NOT_CONNECTED, Profile Identifier: 1
Reported Max Streams: 10, Reported Max OOS Streams: 0
Supported Codec: g729abr8, Maximum Packetization Period: 60
Supported Codec: g729ar8, Maximum Packetization Period: 60
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: g711ulaw, Maximum Packetization Period: 30
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30

Jak zalacze debug to mam:

Kod: Zaznacz cały

May 30 2014 00:37:40.619 CEST: SCCP:rcvd RegisterRejectMessage
May 30 2014 00:37:40.619 CEST: sccp_appl_service_stop_timer: Stop 4CC59694 timer
May 30 2014 00:37:40.619 CEST: sccp_parse_control_msg_v1: rcvd register rej, reason: Max Phones Exceeded
May 30 2014 00:37:40.619 CEST: sccp_initiate_ccm_connect_interval_timer: Start CCM connect interval timer for prof_id 1, appl_type 2, interval 64

Nie rozumiem komunikatu Max Phones Exceeded. Troche sie glowilem nad tym i zastanawiam sie czy to nie jest zwiazane z wersja cucm jaka musialem podac przy definicji
sccp ccm 192.168.1.1 identifier 1 version 7.0+. Nie mozna podac 8.6

Sh run

Kod: Zaznacz cały

no ip domain lookup
no ipv6 cef
!
multilink bundle-name authenticated
!
stcapp ccm-group 1
stcapp
!
!
!
isdn switch-type primary-ni
!
!
!
!
!
!
!
voice-card 0
 dspfarm
 dsp services dspfarm

mgcp profile default
!
sccp local FastEthernet0/1.10
sccp ccm 192.168.1.1 identifier 1 version 7.0
sccp ip precedence 3
sccp
!
sccp ccm group 1
 bind interface FastEthernet0/1.10
 associate ccm 1 priority 1
 associate profile 1 register mtp001906528fa9
 keepalive retries 5
 switchover method immediate
 switchback method immediate
 switchback interval 5
!
dspfarm profile 1 transcode
 codec g729abr8
 codec g729ar8
 codec g711alaw
 codec g711ulaw
 maximum sessions 5
 associate application SCCP

telephony-service
 pin 1234
 max-ephones 40
 max-dn 20
 ip source-address 192.168.1.1 port 2000
 auto assign 10 to 20
 system message WELCOME IN CUCME
 cnf-file location flash:
 load 7960-7940 P00308010200.loads
 time-format 24
 max-conferences 8 gain -6
 call-forward pattern ....
 moh music-on-hold.au
 web admin system name webadmin secret 5 $1$AGbz$Zl7ePWx0Z.GZshA5B34hz1
 dn-webedit
 time-webedit
 transfer-system full-consult
 directory entry 1 122 name EMERGENCY LINE
 create cnf-files version-stamp 7960 May 30 2014 02:44:14

Dziekuje ze wszelkie pomysly

EDIT: Do listingów konfiguracji, show, debug, etc używamy znaczników

Kod: Zaznacz cały

 :!:
Seba

Maciek_JG · #2

Sprobuj pobawic sie tymi dwoma parametrami.

max-ephones 40
max-dn 20

Moze masz za malo "directory numbers" (max-dn) dla Twojej sieci .
Zobacz sobie ile max ephone's i dn's obsluguje Twoj router i dostosuj ustawienia.

Sagittarius · #3

Dziekuje za odpowiedz. Mam wystarczajaco

Kod: Zaznacz cały

FD3AB1 IP:192.168.1.12 Socket:3 DeviceType:Phone has unregistered abnormally.
CME_Voice#sh tel
CME_Voice#sh telephony-service
CONFIG (Version=8.6)
=====================
Version 8.6
Max phoneload sccp version 17
Max dspfarm sccp version 18
Cisco Unified Communications Manager Express
For on-line documentation please see:
http://www.cisco.com/en/US/products/sw/voicesw/ps4625/tsd_products_support_series_home.html

protocol mode default
ip source-address 192.168.1.1 port 2000
ip qos dscp:
 ef (the MS 6 bits, 46, in ToS, 0xB8) for media
 cs3 (the MS 6 bits, 24, in ToS, 0x60) for signal
 af41 (the MS 6 bits, 34, in ToS, 0x88) for video
 default (the MS 6 bits, 0, in ToS, 0x0) for serviceservice directed-pickup
load 7960-7940 P00308010200
max-ephones 40
max-dn 20
max-conferences 8 gain -6
dspfarm units 0
dspfarm transcode sessions 0
conference software
privacy
no privacy-on-hold
hunt-group report delay 1 hours
hunt-group logout DND
max-redirect 10
cnf-file location: flash:
cnf-file option: PER-PHONE-TYPE
network-locale[0] US   (This is the default network locale for this box)
network-locale[1] US
network-locale[2] US
network-locale[3] US
network-locale[4] US
user-locale[0] US    (This is the default user locale for this box)
user-locale[1] US
user-locale[2] US
user-locale[3] US
user-locale[4] US
srst mode auto-provision is OFF
srst ephone template is 0
srst dn template is 0
srst dn line-mode single
moh music-on-hold.au
time-format 24
date-format mm-dd-yy
timezone 0 Greenwich Standard Time
call-forward pattern ....
no transfer-pattern is configured, transfer is restricted to local SCCP phones only.
keepalive 30 auxiliary 30
timeout interdigit 10
timeout busy 10
timeout ringing 180
timeout transfer-recall 0
timeout ringin-callerid 8
timeout night-service-bell 12
caller-id name-only: enable
system message WELCOME IN CUCME
web admin system name webadmin  secret 5 $1$AGbz$Zl7ePWx0Z.GZshA5B34hz1
web admin customer name Customer
edit DN through Web:  enabled.
edit TIME through web:  enabled.
background save interval 10 minutes
Log (table parameters):
     max-size: 150
     retain-timer: 15
create cnf-files version-stamp 7960 May 30 2014 15:50:28
transfer-system full-consult
transfer-digit-collect new-call
auto assign 10 to 20
local directory service: enabled.
Extension-assigner tag-type ephone-tag.

Zmienilem miedzy czasie sccp local interface-type interface-number z fa0/1.10 192.168.1.1 ( ten na ktorm operuje CUCME ) na loopback 1.1.1.1 bo gdzies pisalo ze tak lepiej, ale nie ma roznicy. A na dodatek w sh ephone summary jest to:

Kod: Zaznacz cały

 
Standby socket list (no registered device):
[1]: 1.1.1.1 39336    [4]: 1.1.1.1 26924
[5]: 1.1.1.1 49575    [6]: 1.1.1.1 35039
[7]: 1.1.1.1 64729

Max Conferences 8 with 0 active (8 allowed)


Moze jest jakis BUG w tej wersji, ale nie doszukalem sie nigdzie takiej informacji.

[/code]

Kyniu · #4

Ale właściwie to co Ty konfigurujesz? CUCME czy CUCM? Po co wskazujesz jakieś serwery z zasobami DSP?

Sagittarius · #5

Chce skonfigurowac MOH na CUCME na 2811

Kyniu · #6

Z tego co widzę masz skonfigurowany "moh music-on-hold.au".

PaJacek · #7

Czesc,

Sagittarius pisze:Witam, Mam taki problem.
Kod: Zaznacz cały
Transcoding Oper State: ACTIVE_IN_PROGRESS - Cause Code: CCM_REGISTER_FAILED

Co do tego to widac nie przeczytales manuala wiec nie wszystko skonfigurowales...

http://www.cisco.com/c/en/us/td/docs/vo ... trnsc.html

Nie rozumiem komunikatu Max Phones Exceeded. Troche sie glowilem nad tym i zastanawiam sie czy to nie jest zwiazane z wersja cucm jaka musialem podac przy definicji
sccp ccm 192.168.1.1 identifier 1 version 7.0+. Nie mozna podac 8.6

Nie ma to znaczenia... 7.0+ oznacza wszystkie nowsze wersje od 7.0... jak i sama 7.0..

Max Phone Exceded oznacza, ze przekraczasz zadeklarowana wartosc w komendzie max-ephones... anyway.. Transcoder nie moze zarejestrowac sie jak zwykly ephone...

Kod: Zaznacz cały

telephony-service
 max-ephones 40
 .
 .
 moh music-on-hold.au
 .

[/quote]

Pomijajac fakt, ze nie wiadomo co chcesz skonfigurowac... konfiguracja funkcji transcoder'a jest niedokonfigurowana... generalnie nie wiem po co Ci ona...
Jezeli chodzi o moh.. jak widac, skonfigurowane jest w wersji unicastowej i uzywany bedzie codec g711... pytanie czy masz taki plik we flash'u... moh bedzie udostepniany w LAN'ie i na voice-port'ach... Z tego co pamietam na WAN chyba nie powinien wychodzic by default, chyba, ze cos sie zmienilo.. zreszta wysylanie moh codec'iem g711 po WAN'ie to chyba taki sobie pomysl..

CCIE.pl

CUCME TRANSCODING FEIL

CUCME TRANSCODING FEIL

Re: CUCME TRANSCODING FEIL