Witam
Mam router 2811 i chcę podłączyć 2 razy HWIC-4ESW oraz jeden WIC2T. Niestety jeden HWIC nie działa ( sprzętowo jest wykrywany ale wygląda ze nie dziala ) Czy są jakies ograniczenia albo wytyczne dotyczące włączenie 2 HWICów i jednego WIC2T.
Prosze o pomoc.
Pozdrawiam
problem !! 2811 + 2razy HWIC-4ESW + WIC2T
sh diag
sh ver
czytales http://tinyurl.com/bjk5c podstawowe:
* Prerequisites for EtherSwitch HWICs
* Restrictions for EtherSwitch HWICs
?
No more than two Ethernet Switch HWICs or network modules may be installed in a host router.
Multiple Ethernet Switch HWICs or network modules installed in a host router will not act independently of each other. They must be stacked, as they will not work at all otherwise.
PJ
sh ver
czytales http://tinyurl.com/bjk5c podstawowe:
* Prerequisites for EtherSwitch HWICs
* Restrictions for EtherSwitch HWICs
?
No more than two Ethernet Switch HWICs or network modules may be installed in a host router.
Multiple Ethernet Switch HWICs or network modules installed in a host router will not act independently of each other. They must be stacked, as they will not work at all otherwise.
PJ
Gdybys nie mial dostepu:
Cisco HWIC-4ESW and HWIC-D-9ESW EtherSwitch Interface Cards
* Configuring Stacking
Stacking is the connection of two switch modules resident in the same chassis so that they behave as a single switch. When a chassis is populated with two switch modules, the user must configure both of them to operate in stacked mode. This is done by selecting one port from each switch module and configuring it to be a stacking partner. The user must then connect with a cable the stacking partners from each switch module to physically stack the switch modules. Any one port in a switch module can be designated as the stacking partner for that switch module.
Beginning in privileged EXEC mode, follow these steps to configure a pair of ports on two different switch modules as stacking partners.
SUMMARY STEPS
1. interface fastethernet interface-id
2. no shutdown
3. switchport stacking-partner interface FastEthernet partner-interface-id
4. exit
5. interface fastethernet partner-interface-id
6. no shutdown
7. end
Note: Both stacking partner ports must have their speed and duplex parameters set to auto.
Caution: If stacking is removed, stacked interfaces will go to shutdown state. Other non-stacked ports will be left unchanged.
Heh, czyli z tego co rozumiem musisz je skonfigurowac odpowiednio i spiac kabelkiem. :)
PJ
Cisco HWIC-4ESW and HWIC-D-9ESW EtherSwitch Interface Cards
* Configuring Stacking
Stacking is the connection of two switch modules resident in the same chassis so that they behave as a single switch. When a chassis is populated with two switch modules, the user must configure both of them to operate in stacked mode. This is done by selecting one port from each switch module and configuring it to be a stacking partner. The user must then connect with a cable the stacking partners from each switch module to physically stack the switch modules. Any one port in a switch module can be designated as the stacking partner for that switch module.
Beginning in privileged EXEC mode, follow these steps to configure a pair of ports on two different switch modules as stacking partners.
SUMMARY STEPS
1. interface fastethernet interface-id
2. no shutdown
3. switchport stacking-partner interface FastEthernet partner-interface-id
4. exit
5. interface fastethernet partner-interface-id
6. no shutdown
7. end
Note: Both stacking partner ports must have their speed and duplex parameters set to auto.
Caution: If stacking is removed, stacked interfaces will go to shutdown state. Other non-stacked ports will be left unchanged.
Heh, czyli z tego co rozumiem musisz je skonfigurowac odpowiednio i spiac kabelkiem. :)
PJ