CCIE.pl

site 4 CCIE wannabies
https://ccie.pl/

Cisco EHWIC-4G-LTE-G w sieci Plus

https://ccie.pl/viewtopic.php?f=46&t=20556

Strona 1 z 2

Cisco EHWIC-4G-LTE-G w sieci Plus

: 30 paź 2014, 20:50
autor: czuker
Witam,

Czy udało się komuś skonfigurować router z karta Cisco EHWIC-4G-LTE-G do współpracy z siecią Plus? Byłbym wdzięczny za przykładowy config.

Pozdrawiam
darek

: 31 paź 2014, 07:41
autor: aron
Co prawda to co ponizej to cyfrowy polsat ale to przeciez w koncu to samo;) Musisz tylko ustawic inny APN. "internet" zamiast "internet.cp"

Kod: Zaznacz cały


chat-script lte "" "AT!CALL" TIMEOUT 60 "OK"

interface Cellular0/0/0
 ip address negotiated
 ip nat outside
 ip virtual-reassembly in
 encapsulation slip
 dialer in-band
 dialer pool-member 1
 dialer-group 1

interface Dialer1
 ip address negotiated
 ip nat outside
 ip virtual-reassembly in
 encapsulation slip
 dialer pool 1
 dialer idle-timeout 0
 dialer string lte
 dialer persistent
 dialer-group 1
!

#show cellular 0/0/0 all
Hardware Information
====================
Modem Firmware Version = SWI9200X_03.05.19.04
Modem Firmware built = 2012/09/17 17:57:14
Hardware Version = 10
International Mobile Subscriber Identity (IMSI) = xxxxxxxxxxxx
International Mobile Equipment Identity (IMEI) = xxxxxxxxxxxx
Integrated Circuit Card ID (ICCID) = xxxxxxxxxxxxx
Mobile Subscriber International Subscriber
IDentity Number (MSISDN) = 
Current Modem Temperature = 0 deg C

Profile Information
====================

Profile 1 = ACTIVE* **
--------
PDP Type = IPv4
PDP address = x.y.z.v
Access Point Name (APN) = internet.cp
Authentication = None
Username: internet
Password: internet
	Primary DNS address = 212.2.96.53
	Secondary DNS address = 212.2.96.54

  * - Default profile 
 ** - LTE attach profile


Data Connection Information
===========================
Data Transmitted = 0 bytes, Received = 0 bytes
Profile 1, Packet Session Status = ACTIVE
	IP address = x.y.z.v
	Primary DNS address = 212.2.96.53
	Secondary DNS address = 212.2.96.54
Profile 2, Packet Session Status = INACTIVE
	Inactivity Reason = Unknown
Profile 3, Packet Session Status = INACTIVE
	Inactivity Reason = Unknown
Profile 4, Packet Session Status = INACTIVE
	Inactivity Reason = Unknown
Profile 5, Packet Session Status = INACTIVE
	Inactivity Reason = Unknown
Profile 6, Packet Session Status = INACTIVE
	Inactivity Reason = Unknown
Profile 7, Packet Session Status = INACTIVE
	Inactivity Reason = Unknown
Profile 8, Packet Session Status = INACTIVE
	Inactivity Reason = Unknown
Profile 9, Packet Session Status = INACTIVE
	Inactivity Reason = Unknown
Profile 10, Packet Session Status = INACTIVE
	Inactivity Reason = Unknown
Profile 11, Packet Session Status = INACTIVE
	Inactivity Reason = Unknown
Profile 12, Packet Session Status = INACTIVE
	Inactivity Reason = Unknown
Profile 13, Packet Session Status = INACTIVE
	Inactivity Reason = Unknown
Profile 14, Packet Session Status = INACTIVE
	Inactivity Reason = Unknown
Profile 15, Packet Session Status = INACTIVE
	Inactivity Reason = Unknown
Profile 16, Packet Session Status = INACTIVE
	Inactivity Reason = Unknown

Network Information
===================
Current System Time = Fri Oct 31 6:42:28 2014
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = 260 - 1
Mobile Country Code (MCC) = 260
Mobile Network Code (MNC) = 1
Packet switch domain(PS) state = Attached
Registration state(EMM) = Registered
Tracking Area Code (TAC) = 19002
Cell ID = 3745538
Primary Scrambling Code = 65535

Radio Information
=================
Radio power mode = ON
Channel Number = 1300
Current Band = LTE
Current RSSI = -67 dBm
Current RSRP = -97  dBm
Current RSRQ = -7  dB
Current SNR = 19.8  dB
LTE Technology Preference = LTE
LTE Technology Selected = LTE

Modem Security Information
==========================
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of CHV1 Retries remaining = 3

GPS Information
==========================

GPS Info
-------------
GPS Feature: enabled
GPS Port Selected: Dedicated GPS port
GPS State: GPS disabled
          
SMS Information
===============
Incoming Message Information
----------------------------
SMS stored in modem = 13
SMS archived since booting up = 0
Total SMS deleted since booting up = 0
Storage records allocated = 25
Storage records used = 13
Number of callbacks triggered by SMS = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0

Outgoing Message Information
----------------------------
Total SMS sent successfully = 0
Total SMS send failure = 0
Number of outgoing SMS pending = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Last Outgoing SMS Status = SUCCESS
Copy-to-SIM Status =     0x0
Send-to-Network Status = 0x0
Report-Outgoing-Message-Number:
  Reference Number =     0
  Result Code =          0x0
  Diag Code =            0x0 0x0 0x0 0x0 0x0

SMS Archive URL = 

Error Information
=================

This command is not supported on 4G modems.


Modem Crashdump Information
===========================
Modem crashdump logging: off

: 07 lis 2014, 23:37
autor: mayki
Czy udało się komuś skonfigurować router z karta Cisco EHWIC-4G-LTE-G do współpracy z siecią Plus?
Ja właśnie z tym walczę od dwóch dni i d*** :( A Tobie udało się już to odpalić?

: 08 lis 2014, 07:06
autor: aron
Mayki,

Co dokładnie Ci nie działa? Config powyżej jest z działającego routera;)

Pokaz wynik "show cell x/y/z all"

Re: Cisco EHWIC-4G-LTE-G w sieci Plus

: 09 lis 2014, 13:41
autor: vrankom
czuker pisze:Witam,

Czy udało się komuś skonfigurować router z karta Cisco EHWIC-4G-LTE-G do współpracy z siecią Plus? Byłbym wdzięczny za przykładowy config.

Pozdrawiam
darek
mi dziala, zaraz yciagne konfig to ci wrzuce

: 10 lis 2014, 12:49
autor: eljot
To jeszcze ja coś podpowiem

Działa prawidłowo konfiguracja z configuration guide cisco:
tu
Ustawiam tylko wyższy timeout:

Kod: Zaznacz cały

chat-script lte "" "AT!CALL" TIMEOUT 60 "OK"

Profil konfiguruję następująco:

Kod: Zaznacz cały

cellular 0/0/0 lte profile create 2 internet pap_chap plusgsm plusgsm
Zdaje się, że user/password nie są potrzebne, ale tak jak powyżej działa;)

Dwie rzeczy, na które trzeba zwrócić uwagę:
1. Profil się nie podniesie i generalnie nic nie zadziała, jeżeli nie wyślesz ruchu przez interfejs cellular. Trzeba więc skonfigurować routing/nat itp, wysłać ping i poczekać dłuższą chwilę
2. Miałem taki przypadek, że przy niskim poziomie sygnału (RSSI na poziomie -93 dbm) usługa w żaden sposób nie chciała się podnieść, konieczny był restart routera, po którym profil stał się aktywny i usługa zaczęła działać (chociaż tylko na poziomie UMTS - ale to już wina lokalizacji)

Pozdr.

: 10 lis 2014, 23:39
autor: mayki
Hej,

Dzięki za odpowiedzi, jednak nadal mi to nie działa.

Obecna konfiguracja wygląda tak:

Interfejs cel 0/0/0:

Kod: Zaznacz cały

interface Cellular0/0/0
 ip address negotiated
 ip nat outside
 ip virtual-reassembly in
 encapsulation slip
 dialer in-band
 dialer idle-timeout 0
 dialer string lte
 dialer-group 1
 no peer default ip address
 async mode interactive
 routing dynamic
end
chat script:

Kod: Zaznacz cały

chat-script lte "" "AT!CALL" TIMEOUT 60 "OK"
mam skonfigurowany też interfejs loopback (2.2.2.2), który służy mi do testów i jest natowany na tym cel 0/0/0. Dodałem też routing do hosta w internecie ze wskazaniem na int cel 0/0/0

Generalnie to próba połączenia wygląda tak:

Kod: Zaznacz cały

000067: Nov 10 23:32:42.687: Ce0/0/0 DDR: place call
000068: Nov 10 23:32:42.687: Ce0/0/0 DDR: Dialing cause ip (s=2.2.2.2, d=213.180.141.140)
000069: Nov 10 23:32:42.687: Ce0/0/0 DDR: Attempting to dial lte..............................
000070: Nov 10 23:33:42.687: CHAT0/0/0: Chat script lte finished, status = Connection timed out; remote host not responding
000071: Nov 10 23:33:42.687: Ce0/0/0 DDR: disconnecting call........
000072: Nov 10 23:33:57.687: Ce0/0/0 DDR: re-enable timeout
000073: Nov 10 23:33:58.687: Ce0/0/0 DDR: place call
000074: Nov 10 23:33:58.687: Ce0/0/0 DDR: Dialing cause ip (s=2.2.2.2, d=213.180.141.140)
000075: Nov 10 23:33:58.687: Ce0/0/0 DDR: Attempting to dial lte......
Zauważyłem pewien problem z sygnałem sieci więc postanowiłem zejść z LTE do GSM (edge). Niestety to nic nie daje. Profil się nie aktywuje, połączenie się nie podnosi.

Poniżej zrzut z sh cell0/0/0 all

Kod: Zaznacz cały

Hardware Information
====================
Modem Firmware Version = SWI9200X_03.05.19.04
Modem Firmware built = 2012/09/17 17:57:14
Hardware Version = 10
International Mobile Subscriber Identity (IMSI) = xxxxxxxxxxxxxxxxxx
International Mobile Equipment Identity (IMEI) = yyyyyyyyyyyyyyyyyy
Integrated Circuit Card ID (ICCID) = zzzzzzzzzzzzzzzzzzzzzzz
Mobile Subscriber International Subscriber
IDentity Number (MSISDN) =

Profile Information
====================
Profile password Encryption level: 7

Profile 1 = INACTIVE*
--------
PDP Type = IPv4
Access Point Name (APN) = internet
Authentication = Unknown
Username: plusgsm, Password: 05

 * - Default profile

Data Connection Information
===========================
Data Transmitted = 0 bytes, Received = 0 bytes
Profile 1, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 2, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 3, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 4, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 5, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 6, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 7, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 8, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 9, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 10, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 11, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 12, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 13, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 14, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 15, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 16, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown

Network Information
===================
Current Service Status = Normal, Service Error = None
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Country = , Network =
Mobile Country Code (MCC) = 0
Mobile Network Code (MNC) = 0

Radio Information
=================
Radio power mode = Online
Current RSSI = -74 dBm
LTE Technology Preference = GSM
LTE Technology Selected = EDGE

Modem Security Information
==========================
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of CHV1 Retries remaining = 3
Profil:

Kod: Zaznacz cały

cellular 0/0/0 lte profile create 1 internet chap plusgsm plusgsm
Sprawdzałem z poświadczeniami i bez poświadczeń i za każdym razem efekt jest taki sam. Restartowałem również router oraz próbowałem konfiguracji z dialerem.

Z góry dzięki za jakieś dodatkowe sugestie :)

: 11 lis 2014, 08:35
autor: aron
Wyglada na to, ze z jakiegos powodu modem nie podlacza sie do sieci wiec proba "zapiecia" kontekstu nie moze sie udac ;)

Sprobuj wydac komende

Kod: Zaznacz cały

cellular 0/0/0 lte plmn search
i podeslij wynik. Moze trzeba mu pomoc i recznie wskazac siec.

: 11 lis 2014, 12:43
autor: mayki
Po wklepaniu cellular 0/0/0 lte plmn search

Kod: Zaznacz cały

cellular 0/0/0 lte plmn search
Manual PLMN search disabled
Ale wspomniałeś też o ręcznym wskazaniu sieci, więc spróbowałem to wykonać dla sieci plus:

MMC 260
MNC 01

Kod: Zaznacz cały

ROUTER1#cellular 0/0/0 lte plmn select manual 260 01
Invalid PLMN Selection. Only valid PLMNs found
during PLMN search can be selected
Ale jak widać komenda ta zostaje odrzucona.

: 12 lis 2014, 20:24
autor: vrankom

Kod: Zaznacz cały


vrankom#sh inventory
NAME: "CISCO1921/K9", DESCR: "CISCO1921/K9 chassis, Hw Serial#: XXX, Hw Revision: 1.0"
PID: CISCO1921/K9      , VID: V05 , SN: XXX

NAME: "4G WWAN EHWIC - Global Multimode LTE/DC-HSPA+/HSPA+/HSPA/UMTS/EDGE/GPRS on Slot 0 SubSlot 0", DESCR: "4G WWAN EHWIC - Global Multimode LTE/DC-HSPA+/HSPA+/HSPA/UMTS/EDGE/GPRS"
PID: EHWIC-4G-LTE-G    , VID: V01 , SN: XXX

NAME: "Modem 0 on Cellular0/0/0", DESCR: "Sierra Wireless MC7710 4G-G"
PID: MC7710            , VID: 10 , SN: XXX


version 15.4

chat-script lte "" "AT!CALL1" TIMEOUT 20 "OK"
!
controller Cellular 0/0
 lte sim profile 1 ims 1
 lte gps mode standalone
 lte gps nmea
!
interface Cellular0/0/0
 ip address negotiated
 ip nat outside
 ip virtual-reassembly in
 encapsulation slip
 dialer in-band
 dialer pool-member 2
 async mode interactive

interface Dialer2
 ip address negotiated
 ip nat outside
 ip virtual-reassembly in
 encapsulation slip
 dialer pool 2
 dialer idle-timeout 0
 dialer string lte
 dialer persistent
!
line 0/0/0
 script dialer lte
 modem InOut
 no exec
 transport input all
 transport output all
 rxspeed 100000000
 txspeed 50000000

Kod: Zaznacz cały


vrankom#show cellular 0/0/0 radio
Radio power mode = ON
Channel Number = 1300
Current Band = LTE
Current RSSI = -72 dBm
Current RSRP = -100  dBm
Current RSRQ = -9  dB
Current SNR = 8.4  dB
LTE Technology Preference = AUTO
LTE Technology Selected = LTE



vrankom#show cellular 0/0/0 network
Current System Time = Wed Nov 12 19:29:39 2014
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = Plus
Mobile Country Code (MCC) = 260
Mobile Network Code (MNC) = 1
Packet switch domain(PS) state = Attached
Registration state(EMM) = Registered
Tracking Area Code (TAC) = 19001
Cell ID = 3748608
Primary Scrambling Code = 65535

Kod: Zaznacz cały


vrankom#sh ip int brie
Any interface listed with OK? value "NO" does not have a valid configuration

Interface                  IP-Address      OK? Method Status                Protocol
Embedded-Service-Engine0/0 unassigned      YES NVRAM  administratively down down
Cellular0/0/0              unassigned      YES NVRAM  up                    up
CellNMEA0/0/5              unassigned      YES unset  down                  down
Dialer2                    31.2.79.205     YES IPCP   up                    up
NVI0                       unassigned      YES unset  administratively down down

Kod: Zaznacz cały


000171: *Nov 12 19:29:00.095 UTC: %LINK-3-UPDOWN: Interface Cellular0/0/0, changed state to up
000172: *Nov 12 19:29:00.095 UTC: %DIALER-6-BIND: Interface Ce0/0/0 bound to profile Di2
000173: *Nov 12 19:29:00.095 UTC: Dialer2 DirectIP: Install negotiated IP interface address 31.2.79.205
000174: *Nov 12 19:29:01.095 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cellular0/0/0, changed state to up
000175: *Nov 12 19:29:04.487 UTC: ecell_ipc_rx_handler: IPC RX [28]:
000176: *Nov 12 19:29:04.487 UTC: IPC  (40 bytes):
dziala jak trzeba

: 08 lip 2015, 08:52
autor: MatDan
Proszę o informację, czemu 192.168.2.0/24 nie mogą połączyć się z internetem przez iPlus? Gdzie mam błąd?

show running-config

Kod: Zaznacz cały

chat-script lte "" "AT!CALL" TIMEOUT 60 "OK"


interface GigabitEthernet0/0
 description WAN-Router
 ip address xxx.xxx.218.66 255.255.255.248
 ip nat outside
 ip virtual-reassembly in
 duplex auto
 speed auto
!
interface GigabitEthernet0/1
 description Router-LAN
 ip address 192.168.2.1 255.255.255.0 secondary
 ip address 192.168.1.1 255.255.255.0
 ip nat inside
 ip virtual-reassembly in
 duplex auto
 speed auto
!
interface Cellular0/0/0
 description LTE-Router
 ip address negotiated
 ip nat outside
 ip virtual-reassembly in
 encapsulation slip
 dialer in-band
 dialer string lte
 dialer-group 1


ip nat pool LAN-WAN xxx.xxx.218.66 xxx.xxx.218.66 netmask 255.255.255.248
ip nat inside source list 1 pool LAN-WAN overload
ip nat inside source list 2 interface Cellular0/0/0 overload
ip route 0.0.0.0 0.0.0.0 xxx.xxx.218.65
ip route 192.168.2.0 255.255.255.0 Cellular0/0/0


access-list 1 permit 192.168.1.0 0.0.0.255
access-list 2 permit 192.168.2.0 0.0.0.255


line 0/0/0
 script dialer lte
 no exec
show cellular 0/0/0 all

Kod: Zaznacz cały

Hardware Information
====================
Modem Firmware Version = SWI9200X_03.05.24.00
Modem Firmware built = 2013/11/01 21:34:04
Hardware Version = 10
International Mobile Subscriber Identity (IMSI) = xxxxxxxxxxxxxxx
International Mobile Equipment Identity (IMEI) = xxxxxxxxxxxxxxx
Integrated Circuit Card ID (ICCID) = xxxxxxxxxxxxxxxxxx
Mobile Subscriber International Subscriber
IDentity Number (MSISDN) =
Current Modem Temperature = 0 deg C

Profile Information
====================
Profile password Encryption level: 7


Profile 1 = INACTIVE* **
--------
PDP Type = IPv4
Access Point Name (APN) = internet
Authentication = CHAP
Username: plusgsm
Password: plusgsm

  * - Default profile
 ** - LTE attach profile


Data Connection Information
===========================
Data Transmitted = 0 bytes, Received = 0 bytes
Profile 1, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 2, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 3, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 4, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 5, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 6, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 7, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 8, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 9, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 10, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 11, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 12, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 13, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 14, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 15, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 16, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown

Network Information
===================
Current System Time = Wed Jul 8 5:7:49 2015
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = Plus
Mobile Country Code (MCC) = 260
Mobile Network Code (MNC) = 1
Packet switch domain(PS) state = Attached
Registration state(EMM) = Registered
Tracking Area Code (TAC) = 21405
Cell ID = 5848065
Primary Scrambling Code = 65535

Radio Information
=================
Radio power mode = ON
Channel Number = 1300
Current Band = LTE
Current RSSI = -74 dBm
Current RSRP = -99  dBm
Current RSRQ = -6  dB
Current SNR = 21.6  dB
LTE Technology Preference = AUTO
LTE Technology Selected = LTE

Modem Security Information
==========================
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of CHV1 Retries remaining = 3

GPS Information
==========================

GPS Info
-------------
GPS Feature: enabled
GPS Port Selected: Dedicated GPS port
GPS State: GPS disabled

SMS Information
===============
Incoming Message Information
----------------------------
SMS stored in modem = 0
SMS archived since booting up = 0
Total SMS deleted since booting up = 0
Storage records allocated = 25
Storage records used = 0
Number of callbacks triggered by SMS = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0

Outgoing Message Information
----------------------------
Total SMS sent successfully = 0
Total SMS send failure = 0
Number of outgoing SMS pending = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Last Outgoing SMS Status = SUCCESS
Copy-to-SIM Status =     0x0
Send-to-Network Status = 0x0
Report-Outgoing-Message-Number:
  Reference Number =     0
  Result Code =          0x0
  Diag Code =            0x0 0x0 0x0 0x0 0x0

SMS Archive URL =

Error Information
=================

This command is not supported on 4G modems.


Modem Crashdump Information
===========================
Modem crashdump logging: off

: 08 lip 2015, 09:36
autor: aron
Najpierw musisz sprawic aby zapięło Ci sie połączenie do sieci LTE. Na przykład przez taką konfigurację.

Potem musisz pokombinowac z Policy Based Routing bo o ile rozumiem Twoj post to chcesz aby część użytkowników szła przez WAN a część (w tym samym czasie) przez LTE.

: 08 lip 2015, 09:45
autor: vrankom
to jak odpalic ta karte masz pare postow wyzej - moj wpis... ja mam na iplus i smiga, musialem tylko wgrac mowy firmware poniewaz karta miala tendencje do zawieszania sie na starym ;/

: 08 lip 2015, 09:54
autor: Marek607
podepne sie - znajdzie sie coś za 200-300 PLN z logo cisco co obsługuje lte z iplusa?
Obecnie widze same karty lub routery, ale za 1,5k.
oczywiscie uzywane ;)

Re: Cisco EHWIC-4G-LTE-G w sieci Plus

: 13 sty 2017, 14:48
autor: Piron
Witam,
Czy może ktoś podpowiedzieć w jaki sposób aktywować profil inny niż 1? Jak wiadomo profil 1 jest defaultowy, chcę ustawić profil np. 2 jako profil główny.
Mam jeszcze jedno pytanie, w jaki sposób zrobić aby modem nawiązywał sam połączenie nawet jeśli żaden ruch nie zostanie wygenerowany ?
Strefa czasowa UTC+02:00
Strona 1 z 2

Technologię dostarcza phpBB® Forum Software © phpBB Limited

Polski pakiet językowy dostarcza phpBB.pl