Cisco EHWIC-4G-LTE-G w sieci Plus
Cisco EHWIC-4G-LTE-G w sieci Plus
Witam,
Czy udało się komuś skonfigurować router z karta Cisco EHWIC-4G-LTE-G do współpracy z siecią Plus? Byłbym wdzięczny za przykładowy config.
Pozdrawiam
darek
Czy udało się komuś skonfigurować router z karta Cisco EHWIC-4G-LTE-G do współpracy z siecią Plus? Byłbym wdzięczny za przykładowy config.
Pozdrawiam
darek
Co prawda to co ponizej to cyfrowy polsat ale to przeciez w koncu to samo;) Musisz tylko ustawic inny APN. "internet" zamiast "internet.cp"
Kod: Zaznacz cały
chat-script lte "" "AT!CALL" TIMEOUT 60 "OK"
interface Cellular0/0/0
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation slip
dialer in-band
dialer pool-member 1
dialer-group 1
interface Dialer1
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation slip
dialer pool 1
dialer idle-timeout 0
dialer string lte
dialer persistent
dialer-group 1
!
#show cellular 0/0/0 all
Hardware Information
====================
Modem Firmware Version = SWI9200X_03.05.19.04
Modem Firmware built = 2012/09/17 17:57:14
Hardware Version = 10
International Mobile Subscriber Identity (IMSI) = xxxxxxxxxxxx
International Mobile Equipment Identity (IMEI) = xxxxxxxxxxxx
Integrated Circuit Card ID (ICCID) = xxxxxxxxxxxxx
Mobile Subscriber International Subscriber
IDentity Number (MSISDN) =
Current Modem Temperature = 0 deg C
Profile Information
====================
Profile 1 = ACTIVE* **
--------
PDP Type = IPv4
PDP address = x.y.z.v
Access Point Name (APN) = internet.cp
Authentication = None
Username: internet
Password: internet
Primary DNS address = 212.2.96.53
Secondary DNS address = 212.2.96.54
* - Default profile
** - LTE attach profile
Data Connection Information
===========================
Data Transmitted = 0 bytes, Received = 0 bytes
Profile 1, Packet Session Status = ACTIVE
IP address = x.y.z.v
Primary DNS address = 212.2.96.53
Secondary DNS address = 212.2.96.54
Profile 2, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 3, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 4, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 5, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 6, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 7, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 8, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 9, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 10, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 11, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 12, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 13, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 14, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 15, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 16, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Network Information
===================
Current System Time = Fri Oct 31 6:42:28 2014
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = 260 - 1
Mobile Country Code (MCC) = 260
Mobile Network Code (MNC) = 1
Packet switch domain(PS) state = Attached
Registration state(EMM) = Registered
Tracking Area Code (TAC) = 19002
Cell ID = 3745538
Primary Scrambling Code = 65535
Radio Information
=================
Radio power mode = ON
Channel Number = 1300
Current Band = LTE
Current RSSI = -67 dBm
Current RSRP = -97 dBm
Current RSRQ = -7 dB
Current SNR = 19.8 dB
LTE Technology Preference = LTE
LTE Technology Selected = LTE
Modem Security Information
==========================
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of CHV1 Retries remaining = 3
GPS Information
==========================
GPS Info
-------------
GPS Feature: enabled
GPS Port Selected: Dedicated GPS port
GPS State: GPS disabled
SMS Information
===============
Incoming Message Information
----------------------------
SMS stored in modem = 13
SMS archived since booting up = 0
Total SMS deleted since booting up = 0
Storage records allocated = 25
Storage records used = 13
Number of callbacks triggered by SMS = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Outgoing Message Information
----------------------------
Total SMS sent successfully = 0
Total SMS send failure = 0
Number of outgoing SMS pending = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Last Outgoing SMS Status = SUCCESS
Copy-to-SIM Status = 0x0
Send-to-Network Status = 0x0
Report-Outgoing-Message-Number:
Reference Number = 0
Result Code = 0x0
Diag Code = 0x0 0x0 0x0 0x0 0x0
SMS Archive URL =
Error Information
=================
This command is not supported on 4G modems.
Modem Crashdump Information
===========================
Modem crashdump logging: off
Re: Cisco EHWIC-4G-LTE-G w sieci Plus
mi dziala, zaraz yciagne konfig to ci wrzuceczuker pisze:Witam,
Czy udało się komuś skonfigurować router z karta Cisco EHWIC-4G-LTE-G do współpracy z siecią Plus? Byłbym wdzięczny za przykładowy config.
Pozdrawiam
darek
To jeszcze ja coś podpowiem
Działa prawidłowo konfiguracja z configuration guide cisco:
tu
Ustawiam tylko wyższy timeout:
Profil konfiguruję następująco:
Zdaje się, że user/password nie są potrzebne, ale tak jak powyżej działa;)
Dwie rzeczy, na które trzeba zwrócić uwagę:
1. Profil się nie podniesie i generalnie nic nie zadziała, jeżeli nie wyślesz ruchu przez interfejs cellular. Trzeba więc skonfigurować routing/nat itp, wysłać ping i poczekać dłuższą chwilę
2. Miałem taki przypadek, że przy niskim poziomie sygnału (RSSI na poziomie -93 dbm) usługa w żaden sposób nie chciała się podnieść, konieczny był restart routera, po którym profil stał się aktywny i usługa zaczęła działać (chociaż tylko na poziomie UMTS - ale to już wina lokalizacji)
Pozdr.
Działa prawidłowo konfiguracja z configuration guide cisco:
tu
Ustawiam tylko wyższy timeout:
Kod: Zaznacz cały
chat-script lte "" "AT!CALL" TIMEOUT 60 "OK"
Profil konfiguruję następująco:
Kod: Zaznacz cały
cellular 0/0/0 lte profile create 2 internet pap_chap plusgsm plusgsm
Dwie rzeczy, na które trzeba zwrócić uwagę:
1. Profil się nie podniesie i generalnie nic nie zadziała, jeżeli nie wyślesz ruchu przez interfejs cellular. Trzeba więc skonfigurować routing/nat itp, wysłać ping i poczekać dłuższą chwilę
2. Miałem taki przypadek, że przy niskim poziomie sygnału (RSSI na poziomie -93 dbm) usługa w żaden sposób nie chciała się podnieść, konieczny był restart routera, po którym profil stał się aktywny i usługa zaczęła działać (chociaż tylko na poziomie UMTS - ale to już wina lokalizacji)
Pozdr.
Hej,
Dzięki za odpowiedzi, jednak nadal mi to nie działa.
Obecna konfiguracja wygląda tak:
Interfejs cel 0/0/0:
chat script:
mam skonfigurowany też interfejs loopback (2.2.2.2), który służy mi do testów i jest natowany na tym cel 0/0/0. Dodałem też routing do hosta w internecie ze wskazaniem na int cel 0/0/0
Generalnie to próba połączenia wygląda tak:
Zauważyłem pewien problem z sygnałem sieci więc postanowiłem zejść z LTE do GSM (edge). Niestety to nic nie daje. Profil się nie aktywuje, połączenie się nie podnosi.
Poniżej zrzut z sh cell0/0/0 all
Profil:
Sprawdzałem z poświadczeniami i bez poświadczeń i za każdym razem efekt jest taki sam. Restartowałem również router oraz próbowałem konfiguracji z dialerem.
Z góry dzięki za jakieś dodatkowe sugestie
Dzięki za odpowiedzi, jednak nadal mi to nie działa.
Obecna konfiguracja wygląda tak:
Interfejs cel 0/0/0:
Kod: Zaznacz cały
interface Cellular0/0/0
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation slip
dialer in-band
dialer idle-timeout 0
dialer string lte
dialer-group 1
no peer default ip address
async mode interactive
routing dynamic
end
Kod: Zaznacz cały
chat-script lte "" "AT!CALL" TIMEOUT 60 "OK"
Generalnie to próba połączenia wygląda tak:
Kod: Zaznacz cały
000067: Nov 10 23:32:42.687: Ce0/0/0 DDR: place call
000068: Nov 10 23:32:42.687: Ce0/0/0 DDR: Dialing cause ip (s=2.2.2.2, d=213.180.141.140)
000069: Nov 10 23:32:42.687: Ce0/0/0 DDR: Attempting to dial lte..............................
000070: Nov 10 23:33:42.687: CHAT0/0/0: Chat script lte finished, status = Connection timed out; remote host not responding
000071: Nov 10 23:33:42.687: Ce0/0/0 DDR: disconnecting call........
000072: Nov 10 23:33:57.687: Ce0/0/0 DDR: re-enable timeout
000073: Nov 10 23:33:58.687: Ce0/0/0 DDR: place call
000074: Nov 10 23:33:58.687: Ce0/0/0 DDR: Dialing cause ip (s=2.2.2.2, d=213.180.141.140)
000075: Nov 10 23:33:58.687: Ce0/0/0 DDR: Attempting to dial lte......
Poniżej zrzut z sh cell0/0/0 all
Kod: Zaznacz cały
Hardware Information
====================
Modem Firmware Version = SWI9200X_03.05.19.04
Modem Firmware built = 2012/09/17 17:57:14
Hardware Version = 10
International Mobile Subscriber Identity (IMSI) = xxxxxxxxxxxxxxxxxx
International Mobile Equipment Identity (IMEI) = yyyyyyyyyyyyyyyyyy
Integrated Circuit Card ID (ICCID) = zzzzzzzzzzzzzzzzzzzzzzz
Mobile Subscriber International Subscriber
IDentity Number (MSISDN) =
Profile Information
====================
Profile password Encryption level: 7
Profile 1 = INACTIVE*
--------
PDP Type = IPv4
Access Point Name (APN) = internet
Authentication = Unknown
Username: plusgsm, Password: 05
* - Default profile
Data Connection Information
===========================
Data Transmitted = 0 bytes, Received = 0 bytes
Profile 1, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 2, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 3, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 4, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 5, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 6, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 7, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 8, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 9, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 10, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 11, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 12, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 13, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 14, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 15, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 16, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Network Information
===================
Current Service Status = Normal, Service Error = None
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Country = , Network =
Mobile Country Code (MCC) = 0
Mobile Network Code (MNC) = 0
Radio Information
=================
Radio power mode = Online
Current RSSI = -74 dBm
LTE Technology Preference = GSM
LTE Technology Selected = EDGE
Modem Security Information
==========================
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of CHV1 Retries remaining = 3
Kod: Zaznacz cały
cellular 0/0/0 lte profile create 1 internet chap plusgsm plusgsm
Z góry dzięki za jakieś dodatkowe sugestie
Wyglada na to, ze z jakiegos powodu modem nie podlacza sie do sieci wiec proba "zapiecia" kontekstu nie moze sie udac
Sprobuj wydac komende i podeslij wynik. Moze trzeba mu pomoc i recznie wskazac siec.
Sprobuj wydac komende
Kod: Zaznacz cały
cellular 0/0/0 lte plmn search
Po wklepaniu cellular 0/0/0 lte plmn search
Ale wspomniałeś też o ręcznym wskazaniu sieci, więc spróbowałem to wykonać dla sieci plus:
MMC 260
MNC 01
Ale jak widać komenda ta zostaje odrzucona.
Kod: Zaznacz cały
cellular 0/0/0 lte plmn search
Manual PLMN search disabled
MMC 260
MNC 01
Kod: Zaznacz cały
ROUTER1#cellular 0/0/0 lte plmn select manual 260 01
Invalid PLMN Selection. Only valid PLMNs found
during PLMN search can be selected
Kod: Zaznacz cały
vrankom#sh inventory
NAME: "CISCO1921/K9", DESCR: "CISCO1921/K9 chassis, Hw Serial#: XXX, Hw Revision: 1.0"
PID: CISCO1921/K9 , VID: V05 , SN: XXX
NAME: "4G WWAN EHWIC - Global Multimode LTE/DC-HSPA+/HSPA+/HSPA/UMTS/EDGE/GPRS on Slot 0 SubSlot 0", DESCR: "4G WWAN EHWIC - Global Multimode LTE/DC-HSPA+/HSPA+/HSPA/UMTS/EDGE/GPRS"
PID: EHWIC-4G-LTE-G , VID: V01 , SN: XXX
NAME: "Modem 0 on Cellular0/0/0", DESCR: "Sierra Wireless MC7710 4G-G"
PID: MC7710 , VID: 10 , SN: XXX
version 15.4
chat-script lte "" "AT!CALL1" TIMEOUT 20 "OK"
!
controller Cellular 0/0
lte sim profile 1 ims 1
lte gps mode standalone
lte gps nmea
!
interface Cellular0/0/0
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation slip
dialer in-band
dialer pool-member 2
async mode interactive
interface Dialer2
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation slip
dialer pool 2
dialer idle-timeout 0
dialer string lte
dialer persistent
!
line 0/0/0
script dialer lte
modem InOut
no exec
transport input all
transport output all
rxspeed 100000000
txspeed 50000000
Kod: Zaznacz cały
vrankom#show cellular 0/0/0 radio
Radio power mode = ON
Channel Number = 1300
Current Band = LTE
Current RSSI = -72 dBm
Current RSRP = -100 dBm
Current RSRQ = -9 dB
Current SNR = 8.4 dB
LTE Technology Preference = AUTO
LTE Technology Selected = LTE
vrankom#show cellular 0/0/0 network
Current System Time = Wed Nov 12 19:29:39 2014
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = Plus
Mobile Country Code (MCC) = 260
Mobile Network Code (MNC) = 1
Packet switch domain(PS) state = Attached
Registration state(EMM) = Registered
Tracking Area Code (TAC) = 19001
Cell ID = 3748608
Primary Scrambling Code = 65535
Kod: Zaznacz cały
vrankom#sh ip int brie
Any interface listed with OK? value "NO" does not have a valid configuration
Interface IP-Address OK? Method Status Protocol
Embedded-Service-Engine0/0 unassigned YES NVRAM administratively down down
Cellular0/0/0 unassigned YES NVRAM up up
CellNMEA0/0/5 unassigned YES unset down down
Dialer2 31.2.79.205 YES IPCP up up
NVI0 unassigned YES unset administratively down down
Kod: Zaznacz cały
000171: *Nov 12 19:29:00.095 UTC: %LINK-3-UPDOWN: Interface Cellular0/0/0, changed state to up
000172: *Nov 12 19:29:00.095 UTC: %DIALER-6-BIND: Interface Ce0/0/0 bound to profile Di2
000173: *Nov 12 19:29:00.095 UTC: Dialer2 DirectIP: Install negotiated IP interface address 31.2.79.205
000174: *Nov 12 19:29:01.095 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cellular0/0/0, changed state to up
000175: *Nov 12 19:29:04.487 UTC: ecell_ipc_rx_handler: IPC RX [28]:
000176: *Nov 12 19:29:04.487 UTC: IPC (40 bytes):
Proszę o informację, czemu 192.168.2.0/24 nie mogą połączyć się z internetem przez iPlus? Gdzie mam błąd?
show running-config
show cellular 0/0/0 all
show running-config
Kod: Zaznacz cały
chat-script lte "" "AT!CALL" TIMEOUT 60 "OK"
interface GigabitEthernet0/0
description WAN-Router
ip address xxx.xxx.218.66 255.255.255.248
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
!
interface GigabitEthernet0/1
description Router-LAN
ip address 192.168.2.1 255.255.255.0 secondary
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
!
interface Cellular0/0/0
description LTE-Router
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation slip
dialer in-band
dialer string lte
dialer-group 1
ip nat pool LAN-WAN xxx.xxx.218.66 xxx.xxx.218.66 netmask 255.255.255.248
ip nat inside source list 1 pool LAN-WAN overload
ip nat inside source list 2 interface Cellular0/0/0 overload
ip route 0.0.0.0 0.0.0.0 xxx.xxx.218.65
ip route 192.168.2.0 255.255.255.0 Cellular0/0/0
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 2 permit 192.168.2.0 0.0.0.255
line 0/0/0
script dialer lte
no exec
Kod: Zaznacz cały
Hardware Information
====================
Modem Firmware Version = SWI9200X_03.05.24.00
Modem Firmware built = 2013/11/01 21:34:04
Hardware Version = 10
International Mobile Subscriber Identity (IMSI) = xxxxxxxxxxxxxxx
International Mobile Equipment Identity (IMEI) = xxxxxxxxxxxxxxx
Integrated Circuit Card ID (ICCID) = xxxxxxxxxxxxxxxxxx
Mobile Subscriber International Subscriber
IDentity Number (MSISDN) =
Current Modem Temperature = 0 deg C
Profile Information
====================
Profile password Encryption level: 7
Profile 1 = INACTIVE* **
--------
PDP Type = IPv4
Access Point Name (APN) = internet
Authentication = CHAP
Username: plusgsm
Password: plusgsm
* - Default profile
** - LTE attach profile
Data Connection Information
===========================
Data Transmitted = 0 bytes, Received = 0 bytes
Profile 1, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 2, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 3, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 4, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 5, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 6, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 7, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 8, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 9, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 10, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 11, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 12, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 13, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 14, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 15, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 16, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Network Information
===================
Current System Time = Wed Jul 8 5:7:49 2015
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = Plus
Mobile Country Code (MCC) = 260
Mobile Network Code (MNC) = 1
Packet switch domain(PS) state = Attached
Registration state(EMM) = Registered
Tracking Area Code (TAC) = 21405
Cell ID = 5848065
Primary Scrambling Code = 65535
Radio Information
=================
Radio power mode = ON
Channel Number = 1300
Current Band = LTE
Current RSSI = -74 dBm
Current RSRP = -99 dBm
Current RSRQ = -6 dB
Current SNR = 21.6 dB
LTE Technology Preference = AUTO
LTE Technology Selected = LTE
Modem Security Information
==========================
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of CHV1 Retries remaining = 3
GPS Information
==========================
GPS Info
-------------
GPS Feature: enabled
GPS Port Selected: Dedicated GPS port
GPS State: GPS disabled
SMS Information
===============
Incoming Message Information
----------------------------
SMS stored in modem = 0
SMS archived since booting up = 0
Total SMS deleted since booting up = 0
Storage records allocated = 25
Storage records used = 0
Number of callbacks triggered by SMS = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Outgoing Message Information
----------------------------
Total SMS sent successfully = 0
Total SMS send failure = 0
Number of outgoing SMS pending = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Last Outgoing SMS Status = SUCCESS
Copy-to-SIM Status = 0x0
Send-to-Network Status = 0x0
Report-Outgoing-Message-Number:
Reference Number = 0
Result Code = 0x0
Diag Code = 0x0 0x0 0x0 0x0 0x0
SMS Archive URL =
Error Information
=================
This command is not supported on 4G modems.
Modem Crashdump Information
===========================
Modem crashdump logging: off
Najpierw musisz sprawic aby zapięło Ci sie połączenie do sieci LTE. Na przykład przez taką konfigurację.
Potem musisz pokombinowac z Policy Based Routing bo o ile rozumiem Twoj post to chcesz aby część użytkowników szła przez WAN a część (w tym samym czasie) przez LTE.
Potem musisz pokombinowac z Policy Based Routing bo o ile rozumiem Twoj post to chcesz aby część użytkowników szła przez WAN a część (w tym samym czasie) przez LTE.
Re: Cisco EHWIC-4G-LTE-G w sieci Plus
Witam,
Czy może ktoś podpowiedzieć w jaki sposób aktywować profil inny niż 1? Jak wiadomo profil 1 jest defaultowy, chcę ustawić profil np. 2 jako profil główny.
Mam jeszcze jedno pytanie, w jaki sposób zrobić aby modem nawiązywał sam połączenie nawet jeśli żaden ruch nie zostanie wygenerowany ?
Czy może ktoś podpowiedzieć w jaki sposób aktywować profil inny niż 1? Jak wiadomo profil 1 jest defaultowy, chcę ustawić profil np. 2 jako profil główny.
Mam jeszcze jedno pytanie, w jaki sposób zrobić aby modem nawiązywał sam połączenie nawet jeśli żaden ruch nie zostanie wygenerowany ?