2811 + DSL

Wszystko co nie mieści się w pozostałych kategoriach
Wiadomość
Autor
slawsop
member
member
Posty: 39
Rejestracja: 15 paź 2009, 19:50
Lokalizacja: Sop

#16

#16 Post autor: slawsop »

Witam .....

Kod: Zaznacz cały

sh access-list 100 
- nie ma nic

Kod: Zaznacz cały

sh access-list 10

Standard IP access list 10
10 permit 192.168.0.0, wildcard bits 0.0.0.255

Kod: Zaznacz cały

Router3#ping 194.204.152.34 source fastEthernet 0/1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 194.204.152.34, timeout is 2 seconds:
Packet sent with a source address of 70.100.200.202
.....
Success rate is 0 percent (0/5)

Kod: Zaznacz cały

Router3#ping 194.204.152.34 source fastEthernet 0/0

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 194.204.152.34, timeout is 2 seconds:
Packet sent with a source address of 192.168.0.1
.....
Success rate is 0 percent (0/5)

Kod: Zaznacz cały

sh ip nat translation
- nic nie ma


all po ustawieniu fa 0/0 i fa 0/1 na duplex-full

podlacze hosta pod router ... i zobacze czy cos to da ...
nat pewnie nie dziala jak w sh ip nat translation pusto ...

Roxx
wannabe
wannabe
Posty: 153
Rejestracja: 17 sty 2008, 12:56
Lokalizacja: Krakow

#17

#17 Post autor: Roxx »

No ale jak nat ma działać jak nie masz łączności z routera na świat?

A interface WAN jest w ogóle podniesiony?

pokaż

Kod: Zaznacz cały

show interfaces fastEthernet 0/1

slawsop
member
member
Posty: 39
Rejestracja: 15 paź 2009, 19:50
Lokalizacja: Sop

#18

#18 Post autor: slawsop »

fa 0/1 zyje ...

Kod: Zaznacz cały

FastEthernet0/1 is up, line protocol is up
  Hardware is MV96340 Ethernet, address is 0017.e069.90d1 (bia 0017.e069.90d1)
  Description: Polaczenie dla sieci InternetDSL$ETH-WAN$
  Internet address is 70.100.200.202/29
  MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 100Mb/s, 100BaseTX/FX
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:23:09, output 00:00:05, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     651 packets input, 48672 bytes
     Received 433 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog
     0 input packets with dribble condition detected
     16344 packets output, 986156 bytes, 0 underruns
     0 output errors, 0 collisions, 2 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out

Kod: Zaznacz cały

Router3#sh ip nat statistics
Total active translations: 0 (0 static, 0 dynamic; 0 extended)
Outside interfaces:
  FastEthernet0/1
Inside interfaces:
  FastEthernet0/0
Hits: 0  Misses: 0
CEF Translated packets: 0, CEF Punted packets: 0
Expired translations: 0
Dynamic mappings:
-- Inside Source
[Id: 1] access-list 10 interface FastEthernet0/1 refcount 0
Queued Packets: 0

Roxx
wannabe
wannabe
Posty: 153
Rejestracja: 17 sty 2008, 12:56
Lokalizacja: Krakow

#19

#19 Post autor: Roxx »

No to może ping do modemu?

Kod: Zaznacz cały

ping 70.100.200.201

Awatar użytkownika
vrankom
wannabe
wannabe
Posty: 1075
Rejestracja: 21 lis 2006, 10:27
Lokalizacja: Warsaw
Kontakt:

#20

#20 Post autor: vrankom »

nie dziala bo wogole nie wychodzisz na swiat...
tak jak przedmowca sugeruje ping na modem...

V.

Kyniu
wannabe
wannabe
Posty: 3595
Rejestracja: 04 lis 2006, 16:23
Kontakt:

Re: 2811 + DSL

#21

#21 Post autor: Kyniu »

slawsop pisze:Witam, mecze sie i mecze ....i nie idzie ....moze ktos madrzejszy pomoże ....
Tak to jeszcze długo może to potrwać. Napisz z jakiego jesteś miasta i co możesz zaproponować. Np. sześciopak piwa i fajne koleżanki w pracy :-) Może ktoś się skusi.

Kyniu

slawsop
member
member
Posty: 39
Rejestracja: 15 paź 2009, 19:50
Lokalizacja: Sop

#22

#22 Post autor: slawsop »

Kod: Zaznacz cały

ping 70.100.200.201
idzie z routera
ze stacji koncze na adresie fa 0/1 70.100.200.202

z routera koncze na 70.100.200.201 dalej nie idzie .... na dns rowniez ...

aron
CCIE
CCIE
Posty: 561
Rejestracja: 05 paź 2004, 18:46
Lokalizacja: waw, PL

#23

#23 Post autor: aron »

no to zglos to do TP i powiedz zeby naprawili;)

slawsop
member
member
Posty: 39
Rejestracja: 15 paź 2009, 19:50
Lokalizacja: Sop

#24

#24 Post autor: slawsop »

to chyba jednak nie sprawa TP .... dsl a podlaczam do kompa wpisuje adresy i net hula ...
sdm pokazuje przy test connections .... najpierw...problem z dns skonfiguruj na routerze ip domain-lookup ....
skonfigurowałem ... podając:

Kod: Zaznacz cały

r#(config)ip domain-lookup source-interface fastEthernet 0/1
potem ...wywala bład tez przy dns ach ...ze nie ma ich skonfigurowanyych na routerze ....
i recommended actions: retest connections after configuring DNS server using configure-->additional task -->dns , który to additional task wogole nie dziala ...

a w run-conf mam:

Kod: Zaznacz cały

ip dhcp pool MojeDHCPPLAN
network 192.168.0.0 255.255.255.0
default-router 192.168.0.1
dns-server 194.204.159.1 194.204.152.34
juz mnie - - - strzela ...kable posprawdzałem ...all co mi do głowy przychodzi ...

slawsop
member
member
Posty: 39
Rejestracja: 15 paź 2009, 19:50
Lokalizacja: Sop

#25

#25 Post autor: slawsop »

SDM o dnsy przestał wolac jak dodałem tu:

Kod: Zaznacz cały

ip domain name xxx.pl
ip name-server 194.204.159.1
ip name-server 194.204.152.34
no vlan accounting output
teraz przy test connection wywala mi przy exit interface:
ze nie ma skonfigurowanej route do zadnego z DNS servers ...
i Reccomended Actions ...:
Select 'User-specified' option or add a 'host specific/network specific/default' route through this interface and retest connection...

nie kumam co mu chodzi tu ....

Awatar użytkownika
bugi
wannabe
wannabe
Posty: 1345
Rejestracja: 09 lip 2008, 17:50
Lokalizacja: Warsaw Poland

#26

#26 Post autor: bugi »

slawsop pisze:SDM o dnsy przestał wolac jak dodałem tu:

Kod: Zaznacz cały

ip domain name xxx.pl
ip name-server 194.204.159.1
ip name-server 194.204.152.34
no vlan accounting output
teraz przy test connection wywala mi przy exit interface:
ze nie ma skonfigurowanej route do zadnego z DNS servers ...
i Reccomended Actions ...:
Select 'User-specified' option or add a 'host specific/network specific/default' route through this interface and retest connection...

nie kumam co mu chodzi tu ....
a po co Ci te dns na routerze ?:D przecież to na stacjach końcowych ustawiasz , i w ogóle sdm to nie polecany sposób konfiguracji.
CCIE RS#55541
"W ogóle, bracie, jeżeli nie masz na utrzymaniu rodziny, nie grozi ci głód, nie jesteś Tutsi ani Hutu i te sprawy, to wystarczy, że odpowiesz sobie na jedno zajebiście, ale to zajebiście, ważne pytanie: co lubię w życiu robić. A potem zacznij to robić..."
http://www.linkedin.com/in/mariuszbugaj

Awatar użytkownika
vrankom
wannabe
wannabe
Posty: 1075
Rejestracja: 21 lis 2006, 10:27
Lokalizacja: Warsaw
Kontakt:

#27

#27 Post autor: vrankom »

btw. patrze na ten konfig a tam taki kwiatek ;)

wlacz:

Kod: Zaznacz cały

ip routing
ip cef
V.

slawsop
member
member
Posty: 39
Rejestracja: 15 paź 2009, 19:50
Lokalizacja: Sop

#28

#28 Post autor: slawsop »

odpalilem ip routing oraz ip cef .... pinga ładnie do dsla ... dalej niet ...
jakie powinny byc ustawienia enkapsulacji ?
przy testowaniu polaczenia sdm em (sdm em tylko testuje) podpowiada zeby sprawdzic enkapsulacje i dns y ...

Seba
CCIE/CCDE Site Admin
CCIE/CCDE Site Admin
Posty: 6223
Rejestracja: 15 lip 2004, 20:35
Lokalizacja: Warsaw, PL

#29

#29 Post autor: Seba »

Proponuje, zebys wrzucil caly konfig, bo troche zmian chyba po drodze bylo, i przyznam, ze za bardzo nie chce mi sie przelatywac przez dwie strony postow, aby zrozumiec, co jest, a co nie jest skonfigurowane ;)
Skoro mozna pingowac Internet z routera, to pozostaje kwestia albo jakiejs ACL blokujacej ruch od klientow, albo bledow w konfiguracji translacji, albo jakis podstawowych rzeczy jak brak albo zly adres DNS zdefiniowany na PC, zly GW, etc.
"Two things are infinite: the universe and human stupidity; and I'm not sure about the universe."
A. Einstein

slawsop
member
member
Posty: 39
Rejestracja: 15 paź 2009, 19:50
Lokalizacja: Sop

#30

#30 Post autor: slawsop »

Last cfg wyglada tak:

Kod: Zaznacz cały

hostname Router3
!
boot-start-marker
boot-end-marker
!
card type t1 1
logging buffered 51200 warnings
enable secret 5 xxx
enable password 7 xxx
!
no aaa new-model
!
resource policy
!
ip subnet-zero
no ip source-route
ip tcp path-mtu-discovery
ip telnet source-interface FastEthernet0/1
!
!
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.0.1
ip dhcp excluded-address 192.168.0.2 192.168.0.254
!
ip dhcp pool MojeDHCPPLAN
   network 192.168.0.0 255.255.255.0
   default-router 192.168.0.1
!
!
ip domain name xxx.pl
ip name-server 194.204.159.1
ip name-server 194.204.152.34
no vlan accounting output
!
username slawsop privilege 15 secret 5 xxx
!
!
controller T1 1/0
 shutdown
 framing esf
 linecode b8zs
 cablelength long 0db
 channel-group 0 timeslots 1-24 speed 64
!
!
interface FastEthernet0/0
 description Polaczenie dla sieci LAN
 ip address 192.168.0.1 255.255.255.0
 ip nat inside
 duplex full
 speed 100
 no mop enabled
!
interface FastEthernet0/1
 description Polaczenie dla sieci InternetDSL$ETH-WAN$

ip address 70.100.200.202 255.255.255.248
 ip nat outside
 duplex full
 speed 100
 no mop enabled
!
interface Serial0/2/0
 no ip address
 shutdown
 clock rate 2000000
!
interface Serial1/0:0
 no ip address
 shutdown
!
ip classless
ip route 0.0.0.0 0.0.0.0 70.100.200.201
!
ip http server
ip http access-class 23
ip http authentication local
ip http timeout-policy idle 600 life 86400 requests 10000
ip nat inside source list 10 interface FastEthernet0/1 overload
!
access-list 10 permit 192.168.0.0 0.0.0.255
no cdp run
!
control-plane
!
banner login 
!
scheduler allocate 20000 1000
!
end

Kod: Zaznacz cały

FastEthernet0/0 is up, line protocol is up
  Hardware is MV96340 Ethernet, address is 0017.e069.90d0 (bia 0017.e069.90d0)
  Description: Polaczenie dla sieci LAN
  Internet address is 192.168.0.1/24
  MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 100Mb/s, 100BaseTX/FX
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:00, output 00:00:07, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 667000 bits/sec, 65 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     1325855 packets input, 1651534667 bytes
     Received 53259 broadcasts, 0 runts, 0 giants, 0 throttles
     1 input errors, 0 CRC, 0 frame, 0 overrun, 1 ignored
     0 watchdog
     0 input packets with dribble condition detected
     59007 packets output, 30935019 bytes, 0 underruns
     0 output errors, 0 collisions, 2 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out

Kod: Zaznacz cały

FastEthernet0/1 is up, line protocol is up
  Hardware is MV96340 Ethernet, address is 0017.e069.90d1 (bia 0017.e069.90d1)
  Description: Polaczenie dla sieci InternetDSL$ETH-WAN$
  Internet address is 70.100.200.202/29
  MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 100Mb/s, 100BaseTX/FX
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 01:09:38, output 00:00:08, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     252 packets input, 31403 bytes
     Received 15 broadcasts, 10 runts, 0 giants, 0 throttles
     10 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog
     0 input packets with dribble condition detected
     166772 packets output, 217796845 bytes, 0 underruns
     0 output errors, 0 collisions, 2 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out




Kod: Zaznacz cały

Router3#show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is 70.100.200.201 to network 0.0.0.0

     70.0.0.0/29 is subnetted, 1 subnets
C       79.100.200.200 is directly connected, FastEthernet0/1
C    192.168.0.0/24 is directly connected, FastEthernet0/0
S*   0.0.0.0/0 [1/0] via 70.100.200.201


pinguje wszystko do DSL'a 70.100.200.201 .... poza dsl a nie wychodze ...

ODPOWIEDZ