GSR 12406 - Straty pakietów na wszystkich portach

Wszystkie rozmowy związane z problemem z hardwarem, supportowanymi funkcjonalnościami, wydajnością urządzeń itp.
Wiadomość
Autor
MCzer
newbie
newbie
Posty: 1
Rejestracja: 29 lip 2016, 22:01

GSR 12406 - Straty pakietów na wszystkich portach

#1

#1 Post autor: MCzer »

Witam.
Mam w sieci Router Cisco GSR 12406 w konfiguracji
1 Route Processor Card
2 Clock Scheduler Cards
5 Switch Fabric Cards
2 T1/E1 BITS controllers
1 ISE 10G SPA Interface Card (12000-SIP-600)
3 Ethernet/IEEE 802.3 interface(s)
10 GigabitEthernet/IEEE 802.3 interface(s)
2043K bytes of non-volatile configuration memory.
cisco 12410/PRP (MPC7457) processor (revision 0x00) with 2097152K bytes of memory.
MPC7457 CPU at 1263Mhz, Rev 1.1, 512KB L2, 2048KB L3 Cache
Od wczoraj pojawił się problem ze stratą pakietów przechodzących przez router na poziomie 4% na wszystkich portach.
Router nie jest zbytnio obciążony. CPU ok 15%. Ruch sumarycznie ok 4 Giga/s. Przechodzi również przez niego IPTV w sumie około 600Mbit/s
Polecenie show controllers fia zwraca taki wynik.
Fabric configuration: 10Gbps bandwidth, redundant fabric
Master Scheduler: Slot 17 Backup Scheduler: Slot 16
Fab epoch no 0 Halt count 0

From Fabric FIA Errors
-----------------------
redund overflow 0 cell drops 1291136
cell parity 0
Switch cards present 0x007C Slots 18 19 20 21 22
Switch cards monitored 0x007C Slots 18 19 20 21 22
Slot: 18 19 20 21 22
Name: sfc0 sfc1 sfc2 sfc3 sfc4
-------- -------- -------- -------- --------
los 556877 0 0 0 0
state On Off Off Off Off
crc16 6341032 1291136 1291136 1291136 1291136

To Fabric FIA Errors
-----------------------
sca not pres 0 req error 0 uni fifo overflow 0
grant parity 0 multi req 0 uni fifo undrflow 0
cntrl parity 0 uni req 0
multi fifo 0 empty dst req 0 handshake error 0
cell parity 0
po wejściu na slot 1
LC-Slot1>enable
LC-Slot1#show controllers fia
Fabric configuration: Full bandwidth redundant
Master Scheduler: Slot 17
Fab epoch no 0 Halt count 0

From Fabric FIA Errors
-----------------------
cell fifo parity 0 no 125 MHz clock 0
cell processor ctrl wd error 0 reassembly mem ctrl wd error 0
reassembly mem single ECC 0 reassembly mem multi ECC 0
first last err 544 sequence err 2682 pkt length err 90
Switch cards present: 0x1F
Switch cards monitored: 0x1F
0 1 2 3 4
-------- -------- -------- -------- --------
los 26316000 0 0 0 0
state On Off Off Off Off
crc16 26315988 0 0 0 0
xor error0 0 0 0
cell drops6579000 6579000 6579000 6579000
drop packets from these linecards
0 1 2 3
-------- -------- -------- --------
Unicast High 0 0 0 0
Unicast Low 0 0 0 0
Multicast High0 0 0 0
Multicast Low 0 0 0 0
4 5 6 7
-------- -------- -------- --------
Unicast High 0 0 0 0
Unicast Low 0 0 0 0
Multicast High0 0 0 0
Multicast Low 0 0 0 0
8 9 10 11
-------- -------- -------- --------
Unicast High 0 0 0 0
Unicast Low 0 0 0 0
Multicast High0 0 0 0
Multicast Low 0 0 0 0
12 13 14 15
-------- -------- -------- --------
Unicast High 0 0 0 0
Unicast Low 0 0 0 0
Multicast High0 0 0 0
Multicast Low 0 0 0 0

To Fabric FIA Errors
-----------------------
piranha data parity 0 piranha cmd parity 0
assem fifo data parity 0 assem fifo cmd par 0
sca gnt parity 0 request error 0
cfifo overflow 0 cfifo underflow 0
piranha miss pkt end 0 piranha miss pkt start 0
pir start pkt LT 40b 0 pir mid pkt LT 32b 0 pir end pkt GT 32b 0
output mask all zeros 0 cfifo single ecc 0 cfifo multi ecc 0
pir no even clk 0 pir on odd clk 0 no 150MHz clk 0
Nie wiem czy wynik poleceń ma coś wspólnego z problemem jaki się u nas pojawił. Proszę o podpowiedź co mogę jeszcze sprawdzić i ewentualnie czy mogę zdalnie wyłączyć jedną z kart "switch-fabric"
Pozdrawiam.
MCzer.

ODPOWIEDZ