3550 - brak portów w CLI

Wszystkie rozmowy związane z problemem z hardwarem, supportowanymi funkcjonalnościami, wydajnością urządzeń itp.
Wiadomość
Autor
tomon
wannabe
wannabe
Posty: 58
Rejestracja: 28 paź 2008, 19:14

3550 - brak portów w CLI

#1

#1 Post autor: tomon »

Po odpaleniu dość dawno nieużywanego Switcha 3550 , moim oczom ukazał się dość dziwny konfig. Mianowicie po komendzie: show ip interf brief
brak w odpowiedzi fizycznych portów, pojawiają się tylko Vlany.
Zacząłem drążyć temat ze może coś z konfiguracją nie tak - przywróciłem sprzęt do ustawien fabrycznych - przynajmniej chciałem tak zarobić aby usunąć problem , jednak on nadal występuje :? . za zielony jestem aby cokolwiek stwierdzić a google też za duzo na ten temat mi nie powiedziało.

Z tego co wyczytałem to error ktory się pojawił podczas POST jest nie do naprawy. jesli tak to trudno ale może ktoś mnie nakieruje co mogło być przyczyną takiej awarii.

Failed data line test (3).
addr=0x00000,sent=0x10000000 recv=0x00


Poniżej listing z CLI :

Kod: Zaznacz cały

Switch#reload 
Proceed with reload? [confirm]

*Mar  1 00:37:46.291: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload command.Base ethernet MAC Address: 00:0c:31:60:7d:80
Xmodem file system is available.
The password-recovery mechanism is enabled.
Initializing Flash...
flashfs[0]: 20 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 14969344
flashfs[0]: Bytes available: 1029632
flashfs[0]: flashfs fsck took 27 seconds.
...done Initializing Flash.
Boot Sector Filesystem (bs:) installed, fsid: 3
Loading "flash:c3550-ipservicesk9-mz.122-44.SE6.bin"...#

File "flash:c3550-ipservicesk9-mz.122-44.SE6.bin" uncompressed and installed, entry point: 0x3000
executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco IOS Software, C3550 Software (C3550-IPSERVICESK9-M), Version 12.2(44)SE6, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 09-Mar-09 20:28 by gereddy
Image text-base: 0x00003000, data-base: 0x012A99FC


Initializing flashfs...
flashfs[1]: 20 files, 3 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 14969344
flashfs[1]: Bytes available: 1029632
flashfs[1]: flashfs fsck took 10 seconds.
flashfs[1]: Initialization complete.
...done Initializing flashfs.
POST: CPU Buffer Tests : Begin
POST: CPU Buffer Tests : End, Status Passed
POST: CPU Interface Tests : Begin
POST: CPU Interface Tests : End, Status Passed
POST: Switch Core Tests : Begin
POST: Switch Core Tests : End, Status Passed
POST: CPU Interface 2nd Stage Tests : Begin
POST: CPU Interface 2nd Stage Tests : End, Status Passed
POST: CAM Subsystem Tests : Begin
POST: CAM Subsystem Tests : End, Status Passed
POST: Ethernet Controller Tests : Begin
Failed data line test (3). 
addr=0x00000,sent=0x10000000 recv=0x00
POST: Ethernet Controller Tests : End, Status Passed
INIT: failed satellites initialization
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco WS-C3550-24 (PowerPC) processor (revision H0) with 65526K/8192K bytes of memory.
Processor board ID CAT0710Y053
Last reset from warm-reset
Running Layer2/3 Switching Image

Ethernet-controller 1 has 12 Fast Ethernet/IEEE 802.3 interfaces

Ethernet-controller 2 has 12 Fast Ethernet/IEEE 802.3 interfaces

Ethernet-controller 3 has 1 Gigabit Ethernet/IEEE 802.3 interface
Ethernet-controller 3 failed POST
POST error status : external RAM test failed

Ethernet-controller 4 has 1 Gigabit Ethernet/IEEE 802.3 interface


The password-recovery mechanism is enabled.
384K bytes of flash-simulated NVRAM.
Base ethernet MAC Address: 00:0C:31:60:7D:80
Motherboard assembly number: 73-5700-10
Power supply part number: 34-0966-02
Motherboard serial number: CAT071000A4
Power supply serial number: DCA065222A3
Model revision number: H0
Motherboard revision number: A0
Model number: WS-C3550-24-SMI
System serial number: CAT0710Y053

!!! WARNING: The switch is not usable !!!

         --- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: n

Would you like to terminate autoinstall? [yes]: n



Press RETURN to get started!


*Mar  1 00:00:29.215: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
*Mar  1 00:00:29.835: %SYS-2-NULLCHUNK: Memory requested from Null Chunk -Process= "Init", ipl= 0, pid= 3
-Traceback= 8E27BC 8E2ED0 FADD60 48C580 3FEBE8 3FF020 F715A0 F71638 8EE2AC 8EE4B8 3F5370 3EC080
*Mar  1 00:00:29.867: %SCHED-7-WATCH: Attempt to set uninitialized watched boolean (address 0). -Process= "VLAN Manager", ipl= 0, pid= 128
-Traceback= 8E27BC 8E2ED0 FB6C28 221008 43F9AC 44FAD4 EFEE98 F07C20 F02D48 F0666C F02C60 EFCCA4 3F5370 3EC080
*Mar  1 00:00:31.039: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
*Mar  1 00:00:50.963: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from (tftp://255.255.255.255/network-confg) failed
*Mar  1 00:00:50.967: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from (tftp://255.255.255.255/cisconet.cfg) failed
*Mar  1 00:00:50.967: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from (tftp://255.255.255.255/switch-confg) failed
*Mar  1 00:00:50.971: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from (tftp://255.255.255.255/ciscortr.cfg) failed
*Mar  1 00:00:50.971: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3550 Software (C3550-IPSERVICESK9-M), Version 12.2(44)SE6, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 09-Mar-09 20:28 by gereddy
*Mar  1 00:00:50.983: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Mar  1 00:00:50.983: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Mar  1 00:00:57.579: %LINK-5-CHANGED: Interface Vlan1, changed state to administratively down

!!! WARNING: The switch is not usable !!!
Switch>
Switch>
Switch>
Switch>
Switch>en
Switch#
Switch#
Switch#sh ip interface brief 
Interface              IP-Address      OK? Method Status                Protocol
Vlan1                  unassigned      YES unset  administratively down down    
Switch#

Switch#
Switch#
Switch#sh 
Switch#sh vl
Switch#sh vlan 

VLAN Name                             Status    Ports
---- -------------------------------- --------- -------------------------------
1    default                          active    
1002 fddi-default                     act/unsup 
1003 token-ring-default               act/unsup 
1004 fddinet-default                  act/unsup 
1005 trnet-default                    act/unsup 

VLAN Type  SAID       MTU   Parent RingNo BridgeNo Stp  BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1    enet  100001     1500  -      -      -        -    -        0      0   
1002 fddi  101002     1500  -      -      -        -    -        0      0   
1003 tr    101003     1500  -      -      -        -    -        0      0   
1004 fdnet 101004     1500  -      -      -        ieee -        0      0   
1005 trnet 101005     1500  -      -      -        ibm  -        0      0   

Remote SPAN VLANs
------------------------------------------------------------------------------


Primary Secondary Type              Ports
------- --------- ----------------- ------------------------------------------

Switch#sh
Switch#show pos
Switch#show post 
Stored system POST messages:
POST: CPU Buffer Tests : Begin
POST: CPU Buffer Tests : End, Status Passed
POST: CPU Interface Tests : Begin
POST: CPU Interface Tests : End, Status Passed
POST: Switch Core Tests : Begin
POST: Switch Core Tests : End, Status Passed
POST: CPU Interface 2nd Stage Tests : Begin
POST: CPU Interface 2nd Stage Tests : End, Status Passed
POST: CAM Subsystem Tests : Begin
POST: CAM Subsystem Tests : End, Status Passed
POST: Ethernet Controller Tests : Begin
Failed data line test (3). 
addr=0x00000,sent=0x10000000 recv=0x00
POST: Ethernet Controller Tests : End, Status Passed

!!! WARNING: The switch is not usable !!!

!!! WARNING: The switch is not usable !!!
Switch#
Switch#

Kyniu
wannabe
wannabe
Posty: 3595
Rejestracja: 04 lis 2006, 16:23
Kontakt:

Re: 3550 - brak portów w CLI

#2

#2 Post autor: Kyniu »

Komunikaty są, powiedziałbym, dostatecznie jasne i czytelne:

POST: Ethernet Controller Tests : Begin
Failed data line test (3).
addr=0x00000,sent=0x10000000 recv=0x00


Czyli switch nie przechodzi testu ASIC'a odpowiedzialnego za obsługę Ethernet. W związku z czym grzecznie informuje:

!!! WARNING: The switch is not usable !!!

Co jeszcze jest niejasne?
CCNA: R&S, Security, Wireless, Collaboration. MCSE: Cloud Platform and Infrastructure, Server Infrastructure. ITIL: Foundation. PPL(A)
https://www.facebook.com/itserviceskielce/ :: https://www.linkedin.com/company/itservicespoland :: https://www.linkedin.com/in/krzysztofkania/

tomon
wannabe
wannabe
Posty: 58
Rejestracja: 28 paź 2008, 19:14

Re: 3550 - brak portów w CLI

#3

#3 Post autor: tomon »

Wszystko jasne - ide zakopać switcha ;/

Kyniu
wannabe
wannabe
Posty: 3595
Rejestracja: 04 lis 2006, 16:23
Kontakt:

Re: 3550 - brak portów w CLI

#4

#4 Post autor: Kyniu »

tomon pisze:Wszystko jasne - ide zakopać switcha ;/
Są ciekawsze zastosowania ;)
CCNA: R&S, Security, Wireless, Collaboration. MCSE: Cloud Platform and Infrastructure, Server Infrastructure. ITIL: Foundation. PPL(A)
https://www.facebook.com/itserviceskielce/ :: https://www.linkedin.com/company/itservicespoland :: https://www.linkedin.com/in/krzysztofkania/

Awatar użytkownika
konradrz
CCIE
CCIE
Posty: 400
Rejestracja: 23 sty 2008, 14:21
Lokalizacja: Singapore, SG
Kontakt:

Re: 3550 - brak portów w CLI

#5

#5 Post autor: konradrz »

tomon pisze:Wszystko jasne - ide zakopać switcha ;/
Zanim go zakopiesz, spróbuj może jeszcze "sh interf bri" (bez "ip"). To prawie jak "bez s".

(ale skoro się porty w VLANie 1 nie pokazują, to wiele bym temu słiczowi nie wróżył; kaczka, to maks co z niego może być)

tomon
wannabe
wannabe
Posty: 58
Rejestracja: 28 paź 2008, 19:14

Re: 3550 - brak portów w CLI

#6

#6 Post autor: tomon »

konradrz pisze:spróbuj może jeszcze "sh interf bri" (bez "ip").

Pokazuje tylko VLAN 1 i to wszystko - żadnych fizycznych portów

Awatar użytkownika
judge dredd
wannabe
wannabe
Posty: 214
Rejestracja: 02 sie 2009, 15:23

Re: 3550 - brak portów w CLI

#7

#7 Post autor: judge dredd »

Przynajmniej Ci ładnie powiedział co i jak. Ja miałem kiedyś taką sytuację, że połowa portów w switchu 3560 normalnie była widoczna w konfiguracji, normalnie można było je konfigurować, normalnie reagowały lampki na shut/no shut, normalnie przyjmowały mac-addresy, ale ni chu chu nie przesyłały ruchu z/do podłączonych urządzeń. Ostatecznie Cisco wymieniło na nowy bez dodatkowych pytań, ale co się czasu zeszło na szukanie dziury w całym to moje.

Pozdro!

JD
Zapraszam na szkolenia CCNA prowadzone w pełni on-line (wykłady oraz ćwiczenia ze sprzętem).
Akademia Sieci LANPulse (www.lanpulse.pl)

ODPOWIEDZ