4510R i problemy z Supervisor V-10GE

Wszystkie rozmowy związane z problemem z hardwarem, supportowanymi funkcjonalnościami, wydajnością urządzeń itp.
Wiadomość
Autor
Awatar użytkownika
ciul
wannabe
wannabe
Posty: 290
Rejestracja: 03 lut 2008, 17:46
Kontakt:

4510R i problemy z Supervisor V-10GE

#1

#1 Post autor: ciul »

Supervisory nie chcą się spiąć.

Kod: Zaznacz cały

cisco WS-C4510R (MPC8540) processor (revision 13) with 524288K bytes of memory.

Processor board ID FOX1203HCCG

MPC8540 CPU at 800Mhz, Supervisor V-10GE

Kod: Zaznacz cały

switch#sh redundancy

Redundant System Information :

------------------------------

       Available system uptime = 1 week, 6 days, 8 hours, 17 minutes

Switchovers system experienced = 1

              Standby failures = 3

        Last switchover reason = active unit failed



                 Hardware Mode = Duplex

    Configured Redundancy Mode = Stateful Switchover

     Operating Redundancy Mode = Stateful Switchover

              Maintenance Mode = Disabled

                Communications = Down      Reason: Failure



Current Processor Information :

-------------------------------

               Active Location = slot 2

        Current Software state = ACTIVE

       Uptime in current state = 1 week, 6 days, 8 hours, 16 minutes

                 Image Version = Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(44)SG1, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2008 by Cisco Systems, Inc.

Compiled Wed 09-Jul-08 13:53 by prod_rel_team

        Configuration register = 0x2101



Peer (slot: 1) information is not available because it is in 'DISABLED' state

Po reloadzie "niedziałającego" supervisora

Kod: Zaznacz cały

001391: *Oct  9 10:05:09.368: %C4K_REDUNDANCY-3-SIMPLEX_MODE: The peer Supervisor has been lost

001392: *Oct  9 10:06:52.368: %C4K_REDUNDANCY-6-DUPLEX_MODE: The peer Supervisor has been detected

001393: *Oct  9 10:07:52.368: %C4K_REDUNDANCY-2-HANDSHAKE_TIMEOUT_ACTIVE: The handshake messaging between active and standby has not yet started.
po fizycznym usunięciu

Kod: Zaznacz cały



001394: *Oct  9 10:09:49.472: %C4K_REDUNDANCY-3-SIMPLEX_MODE: The peer Supervisor has been lost

001395: *Oct  9 10:09:50.312: %C4K_IOSMODPORTMAN-6-MODULEOFFLINE: Module 1 is offline

001396: *Oct  9 10:09:51.308: %C4K_IOSMODPORTMAN-6-MODULEREMOVED: Module 1 is removed

001397: *Oct  9 10:10:27.308: %C4K_IOSMODPORTMAN-6-MODULEINSERTED: Module 1 is inserted

001398: *Oct  9 10:11:44.488: %C4K_REDUNDANCY-6-DUPLEX_MODE: The peer Supervisor has been detected

001399: *Oct  9 10:12:44.488: %C4K_REDUNDANCY-2-HANDSHAKE_TIMEOUT_ACTIVE: The handshake messaging between active and standby has not yet started.

001400: *Oct  9 10:17:44.488: %C4K_REDUNDANCY-2-HANDSHAKE_TIMEOUT_ACTIVE: The handshake messaging between active and standby has not yet started.
Dioda status na obydwu supervisorach świeci się na zielono.

Przy reloadzie tego niedziałającego, jak wpiąłem konsolkę to testy przeszły ok, rommon też, napisał że zaczyna ładować IOSa i zamilkł. Konsola przestała reagować.

sh redun hist

Może ktoś spotkał się z podobnym problemem?
zmiana image, teraz jestem dud|i :)

Awatar użytkownika
ciul
wannabe
wannabe
Posty: 290
Rejestracja: 03 lut 2008, 17:46
Kontakt:

#2

#2 Post autor: ciul »

Pomógł reload aktywnego (2) supervisora.
zmiana image, teraz jestem dud|i :)

ODPOWIEDZ