witam,
kupiłem nowe urządzenie Cisco Aironet 702. Mam problem z konfiguracją. Nie działa dostęp przez www oraz przez linie komend do opcji configure terminal.
Poniżej jest zrzucony proces startu urządzenia. Podczas uruchamiana jest kilka błędów typu syntax error.
Po zalogowaniu na domyślne poświadczenia nie jest dostępna opcja configure terminal. Cisco zwraca syntax error. W helpie także nie widać tej opcji.
Czy to jest normalne zachowanie czy może jest jakiś problem obrazem systemu ?
flash size 1MB, sector count = 64
Flash: 1 MB
Fetching MAC Address from 0x87fe3908
eth0: 50:06:04:a6:23:1e
ATHRSF1_PHY: Port 4, Negotiation timeout
Ethernet link down
eth0
Ether initialization ok!
Atheros on-chip NAND FLash Controller Driver, Version 0.1 (c) 2010 Atheros Communications, Ltd.
Ath Nand ID[87ff117c]: 2c:f1:80:95:02
ONFI MICRON MT29F1G08ABADAWP
Micron NAND 128MiB 3,3V 8-bit [128MB]
====== NAND Parameters ======
sc = 0x87ff1158 bbt = 0x87f98360 bbt_size = 0x100 nf_ctrl = 0x344
page = 0x800 block = 0x20000 oob = 0x40
size = 128MB
Setting 0xb8116290 to 0x2a542d0f
Test Size=0x8000000, Start!!
RAM test complete!
PTD Init
MAC address check ok!
boot method:3
Hit "ESC" to stop autoboot: 0
Uncompressed size: 319299 = 0x4DF43
Loading .text @ 0x84000000 (205088 bytes)
Loading .rodata @ 0x84032120 (38400 bytes)
Loading .data @ 0x8403b720 (3200 bytes)
Loading .data.rel.local @ 0x8403c3a0 (992 bytes)
Loading .data.rel @ 0x8403c780 (124 bytes)
Loading .data.rel.ro.local @ 0x8403c7fc (92 bytes)
Loading .data.rel.ro @ 0x8403c858 (960 bytes)
Clearing .bss @ 0x8403cc20 (161112 bytes)
Clearing .scommon @ 0x84064178 (60 bytes)
## Starting application at 0x84000000 ...
IOS Secondary Bootloader - Starting system.
Ath Nand ID: 95:80:f1:2c:00
Using driver version 1 for media type 2
Valid buffers 120
total120 120
success found all blocks
start end 65 72
found in range
high low end 2335 2089 72
Xmodem file system is available.
mifs[0]: 10 files, 2 directories
mifs[0]: Total bytes : 131334144
mifs[0]: Bytes used : 7591936
mifs[0]: Bytes available : 123742208
mifs[0]: mifs fsck took 0 seconds.
Base Ethernet MAC address: 50:06:04:a6:23:1e
Setup MAC....
Waiting for PHY auto negotiation to complete...Port 4 Negogiation timeout.
Ethernet link is down.
Setting Drop CRC Errors, Pause Frames and Length Error frames
: cfg1 0x7 cfg2 0x7114
Loading "flash:/ap1g1-rcvk9w8-mx.152-4.JA/ap1g1-rcvk9w8-mx.152-4.JA"...############################################################################################################################################################################################################################################################################################################################################################
File "flash:/ap1g1-rcvk9w8-mx.152-4.JA/ap1g1-rcvk9w8-mx.152-4.JA" uncompressed and installed, entry point: 0x60080000
executing...
Stop MAC.
AP1G1 Starting...
cp0 timer begin value is set as 1000
prid= 1974C
Starts main.
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, ap1g1 Software (ap1g1-RCVK9W8-M), Version 15.2(4)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 18-Jun-13 14:15 by prod_rel_team
Initializing flashfs...
Ath Nand ID: 95:80:F1:2C:00
Using driver version 1 for media type 2
Valid buffers 120
total120 120
success found all blocks
start end 65 72
found in range
high low end 2335 2089 72
mifs[3]: 10 files, 2 directories
mifs[3]: Total bytes : 131334144
mifs[3]: Bytes used : 7591936
mifs[3]: Bytes available : 123742208
mifs[3]: mifs fsck took 2 seconds.
mifs[3]: Initialization complete.
...done Initializing flashfs.
Base Ethernet MAC address: 50:06:04:A6:23:1E
Waiting for PHY auto negotiation to complete...Port 4 Negogiation timeout.
This product contains cryptographic features and is subject to United
no ip http server
^
% Invalid input detected at '^' marker.
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
%Error opening flash:/ap1g1-rcvk9w8-mx/info (No such file or directory)cisco AIR-CAP702I-E-K9 (MIPS74k) processor (revision 01) with 73728K/57344K bytes of memory.
Processor board ID KWC1717004X
MIPS74k CPU at 40Mhz, revision number 0x0000
Last reset from power-on
LWAPP image version 7.5.1.33
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 50:06:04:A6:23:1E
Part Number : 74-11077-01
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : KWC1717004X
Top Assembly Part Number : 000-00000-00
Top Assembly Serial Number : KWC1717004X
Top Revision Number : 01
Product/Model Number : AIR-CAP702I-E-K9
% Please define a domain-name first.
logging facility kern
^
% Invalid input detected at '^' marker.
logging trap emergencies
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
: Mac unit : 0
: Max segments per packet : 1
: Max tx descriptor count : 128
: Max rx descriptor count : 256
: Mac capability flags : 4400
athr_gmac_hw_setup mac: 0x61953F40
Setting Drop CRC Errors, Pause Frames and Length Error frames
: cfg1 0x7 cfg2 0x7114
*Mar 1 00:00:13.683: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:13.895: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:16.711: %SYS-5-RESTART: System restarted --
Cisco IOS Software, ap1g1 Software (ap1g1-RCVK9W8-M), Version 15.2(4)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 18-Jun-13 14:15 by prod_rel_team
*Mar 1 00:00:16.731: *** not invoke
*Mar 1 00:00:16.751: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:16.755: %CAPWAP-3-ERRORLOG: Failed to load configuration from flash. Resetting to default config
*Mar 1 00:00:16.767: %PARSER-4-BADCFG: Unexpected end of configuration file.
lwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:17.723: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
User Access Verification
Username: Cisco
no bridge-group 1 source-learning
^
% Invalid input detected at '^' marker.
%Default route without gateway, if not a point-to-point interface, may impact performance
Password:
AP5006.04a6.231e>
*Mar 1 00:00:47.195: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:48.195: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
AP5006.04a6.231e>enable
Password:
AP5006.04a6.231e#conf te
^
% Invalid input detected at '^' marker.
Cisco Aironet 702 problem z konfiguracją
Re: Cisco Aironet 702 problem z konfiguracją
Wygląda na obraz typu recovery. Jeśli chcesz konfigurować ten punkt dostępowy via WWW / Console (nie mając kontrolera), to powinieneś zainteresować się obrazem k9w7.lutador pisze:File "flash:/ap1g1-rcvk9w8-mx.152-4.JA/ap1g1-rcvk9w8-mx.152-4.JA" uncompressed and...
Tutaj trochę leciwy, ale ciągle aktualny dokument na ten temat LWAPP mode to Autonomous mode Conversion