AP1260 Password Recovery w trybie Lightweight

Wiadomość

#16

Chyba guzik trzymałeś za krótko skoro zaczął używać softu z flash a nie z TFTP...
LED zmienił się na czerwony?

frontier · #17

Seba pisze:Chyba guzik trzymałeś za krótko skoro zaczął używać softu z flash a nie z TFTP...
LED zmienił się na czerwony?

Nie pamiętam jaki był LED... ale chyba trzymałem dość długo:

Kod: Zaznacz cały

button is pressed, wait for button to be released... 
button pressed for 15 seconds 
process_config_recovery: set IP address and config to default 10.0.0.1

Już śmiga dobrze, przez ROMMON wgrałem po TFTP IOSa do Autonomous.

horac · #18

to teraz po tftp z opcja overwrite i reload wgraj light image i powinno byc ok

Tu jest nawet filmik

https://www.youtube.com/watch?v=wWDrFjwVNb0

frontier · #19

Po konwersji APek nawet nie próbuje się zarejestrować w kontrolerze... jakieś pomysły? Przejrzałem trochę dokumentów o troubleshootingu ale nigdzie nie było co robić jak APek nawet nie szuka kontrolera.

btw. dokładnie taki sam AP i z tym samym recovery image do tego samego WLC rejestruje się poprawnie...

Kod: Zaznacz cały


Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP:  Numonyx P33
Checking for Over Erased blocks
.............................................
Xmodem file system is available.

DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x8200083f, 0x40000000
RQDC, RFDC : 0x80000031, 0x00000218

PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is up.
PCIE1: VC0 is active
64bit PCIE devices
PCIEx: initialization done
flashfs[0]: 8 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31739904
flashfs[0]: Bytes used: 3214848
flashfs[0]: Bytes available: 28525056
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 70:81:05:e7:a7:89
Ethernet speed is 1000 Mb - FULL duplex
Loading "flash:/ap3g1-rcvk9w8-mx/ap3g1-rcvk9w8-mx"...######
File "flash:/ap3g1-rcvk9w8-mx/ap3g1-rcvk9w8-mx" uncompressed and installed, entry point: 0x4000
executing...
enet halted

IOS Secondary Bootloader - Starting system.
FLASH CHIP:  Numonyx P33
Checking for Over Erased blocks
......................................................................
Xmodem file system is available.

DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x8200083f, 0x40000000
RQDC, RFDC : 0x80000031, 0x00000218

PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is up.
PCIE1: VC0 is active
64bit PCIE devices
PCIEx: initialization done
flashfs[0]: 8 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31739904
flashfs[0]: Bytes used: 3214848
flashfs[0]: Bytes available: 28525056
flashfs[0]: flashfs fsck took 10 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 70:81:05:e7:a7:89
Creating Test Kernel diagnostic commands
Radio 0 : Vendor 0x11AB, Device 0x8324
Radio 1 : Vendor 0x11AB, Device 0x8350
Radio 2 : Vendor 0xC1A1, Device 0x2508
Radio 3 : Vendor 0xCC62, Device 0x3EB7
******** AUTOMATIC DDR CALIBRATION UPGRADE LOGIC *********
=== 1. Is original FCS bootloader in BS:?  If not, skip upgrade ===
    ---> original FCS bootloader not detected -- skip upgrade
Boot CMD: 'boot  flash:/ap3g1-rcvk9w8-mx/ap3g1-rcvk9w8-xx;flash:/ap3g1-rcvk9w8-mx/ap3g1-rcvk9w8-mx'
Loading "flash:/ap3g1-rcvk9w8-mx/ap3g1-rcvk9w8-xx"...#######################

File "flash:/ap3g1-rcvk9w8-mx/ap3g1-rcvk9w8-xx" uncompressed and installed, entry point: 0x4000
executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco IOS Software, C1260 Software (AP3G1-RCVK9W8-M), Version 12.4(23c)JA10, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Fri 20-Mar-15 11:24 by prod_rel_team


Proceeding with system init

Proceeding to unmask interrupts
Initializing flashfs...
FLASH CHIP:  Numonyx P33
Checking for Over Erased blocks
..........................................................................
flashfs[1]: 8 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 31481856
flashfs[1]: Bytes used: 3214848
flashfs[1]: Bytes available: 28267008
flashfs[1]: flashfs fsck took 7 seconds.
flashfs[1]: Initialization complete.
flashfs[2]: 0 files, 1 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 11999232
flashfs[2]: Bytes used: 1024
flashfs[2]: Bytes available: 11998208
flashfs[2]: flashfs fsck took 1 seconds.
flashfs[2]: Initialization complete....done Initializing flashfs.

Ethernet speed is 1000 Mb - FULL duplex

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco AIR-LAP1262N-E-K9    (PowerPC460exr) processor (revision A0) with 81910K/49152K bytes of memory.
Processor board ID FCZ1546J0LZ
PowerPC460exr CPU at 666Mhz, revision number 0x18A8
Last reset from power-on
LWAPP image version 7.0.220.0
1 Gigabit Ethernet interface

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 70:81:05:E7:A7:89
Part Number                          : 73-12175-05
PCA Assembly Number                  : 800-32268-05
PCA Revision Number                  : A0
PCB Serial Number                    : FOC15326PHG
Top Assembly Part Number             : 800-33866-01
Top Assembly Serial Number           : FCZ1546J0LZ
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1262N-E-K9   
% Please define a domain-name first.


Press RETURN to get started!


*Mar  1 00:00:09.386: *** CRASH_LOG = YES
Base Ethernet MAC address: 70:81:05:E7:A7:89

*Mar  1 00:00:09.669: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 8 messages)

*Mar  1 00:00:11.695: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar  1 00:00:11.708: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1260 Software (AP3G1-RCVK9W8-M), Version 12.4(23c)JA10, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Fri 20-Mar-15 11:24 by prod_rel_team
*Jun 25 08:04:44.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Jun 25 08:04:44.018: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set radio control and data rate

*Jun 25 08:04:44.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Jun 25 08:04:52.182: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 192.168.42.230, mask 255.255.255.0, hostname AP7081.05e7.a789

*Jun 25 08:05:02.981: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED AIR-CT2504-K9 (8480.2df8.0cc7)
*Jun 25 08:05:03.981: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED AIR-CT2504-K9 (8480.2df8.0cc7)
AP7081.05e7.a789>

#20

To może skonfiguruj AP ze statycznym WLC z palca:

Kod: Zaznacz cały

APXXX#capwap ap controller ip address 192.168.1.10

gdzie 192.168.1.10 to adres WLC interfejsu management

frontier · #21

Seba pisze:To może skonfiguruj AP ze statycznym WLC z palca:
Kod: Zaznacz cały
APXXX#capwap ap controller ip address 192.168.1.10
gdzie 192.168.1.10 to adres WLC interfejsu management

To samo... czyli APek milczy, w ogóle nie chce sie skomunikowac z WLC, na którym takze cicho w logach. APek pojawia sie jedynie w CDP Interface Neighbors.

Kyniu · #22

I kompletnie nic nie wyrzuca na konsoli? Taki APek z softem CAPWAP jest bardzo rozgadany i do tego co chwilę się restartuje jak nie może znaleźć kontrolera. Możesz jeszcze skonfigurować DHCP dla tego AP'eka, wskaż w konfiguracji serwer DNS a na tym serwerze skonfiguruj wpis wskazujący na kontroler jako CISCO-CAPWAP-CONTROLLER

frontier · #23

Kyniu pisze:I kompletnie nic nie wyrzuca na konsoli? Taki APek z softem CAPWAP jest bardzo rozgadany i do tego co chwilę się restartuje jak nie może znaleźć kontrolera. Możesz jeszcze skonfigurować DHCP dla tego AP'eka, wskaż w konfiguracji serwer DNS a na tym serwerze skonfiguruj wpis wskazujący na kontroler jako CISCO-CAPWAP-CONTROLLER

No właśnie nic... ale zamiast tego recovery image wgrałem normalny lightweight, ap3g1-k9w8-tar.124-23c.JA10.tar, ten już gada z kontrolerem więc wszystko działa.