jestem na etapie wykonywania zadania w PT, staję na etapie 85% i nie mam pojęcia czego nie skonfigurowałem aby osiągnąć 100%. Gdy sprawdzam "check results" przy każdym z routerów mam X w drzewie Network->RA->OSPF->Process ID 1-> Networks -> Route 0. Poniżej konfigi routerów i topologia z GNS. Routery tworzą sąsiedztwa, default route propaguje się z RC na inne routery. Z każdego routera jest dostęp do wszystkich prefixów. Nie wiem na ile dużo informacji mogę podać ponieważ to materiał z kursu CCNA...
RA:
hostname RA
!
ip cef
no ipv6 cef
!
license udi pid CISCO1941/K9 sn FTX1524NCYI
!
ip ssh version 1
no ip domain-lookup
!
!
spanning-tree mode pvst
!
interface Loopback0
no ip address
shutdown
!
interface GigabitEthernet0/0
description Link to Multiaccess LAN
ip address 192.168.1.1 255.255.255.0
ip ospf message-digest-key 1 md5 cisco
ip ospf hello-interval 5
ip ospf dead-interval 20
ip ospf priority 150
duplex auto
speed auto
!
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
shutdown
!
interface Vlan1
no ip address
shutdown
!
router ospf 1
log-adjacency-changes
area 0 authentication message-digest
network 192.168.1.1 0.0.0.0 area 0
!
ip classless
!
ip flow-export version 9
!
line con 0
!
line aux 0
!
line vty 0 4
no login
!
!
!
end
RB:
hostname RB
!
ip cef
no ipv6 cef
!
license udi pid CISCO1941/K9 sn FTX1524B55U
!
spanning-tree mode pvst
!
interface Loopback0
no ip address
shutdown
!
interface GigabitEthernet0/0
description Multiaccess LAN
ip address 192.168.1.2 255.255.255.0
ip ospf message-digest-key 1 md5 cisco
ip ospf hello-interval 5
ip ospf dead-interval 20
ip ospf priority 100
duplex auto
speed auto
!
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
shutdown
!
interface Vlan1
no ip address
shutdown
!
router ospf 1
log-adjacency-changes
area 0 authentication message-digest
network 192.168.1.2 0.0.0.0 area 0
!
ip classless
!
ip flow-export version 9
!
line con 0
!
line aux 0
!
line vty 0 4
no login
!
!
!
end
RC:
hostname RC
!
!
ip cef
no ipv6 cef
!
license udi pid CISCO1941/K9 sn FTX152449P8
!
spanning-tree mode pvst
!
interface Loopback0
no ip address
shutdown
!
interface GigabitEthernet0/0
description Link to Mulitaccess LAN
ip address 192.168.1.3 255.255.255.0
ip ospf message-digest-key 1 md5 cisco
ip ospf hello-interval 5
ip ospf dead-interval 20
ip ospf priority 50
duplex auto
speed auto
!
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
shutdown
!
interface Serial0/0/0
ip address 209.165.200.225 255.255.255.252
clock rate 2000000
!
interface Serial0/0/1
no ip address
clock rate 2000000
!
interface Vlan1
no ip address
shutdown
!
router ospf 1
log-adjacency-changes
area 0 authentication message-digest
redistribute static
passive-interface default
no passive-interface GigabitEthernet0/0
network 192.168.1.3 0.0.0.0 area 0
default-information originate
!
ip classless
ip route 0.0.0.0 0.0.0.0 209.165.200.226
!
ip flow-export version 9
!
line con 0
!
line aux 0
!
line vty 0 4
no login
!
!
!
end
michaliwanczuk pisze:Jak dla mnie wygląda ze źle robisz jedna rzecz:
Zamiast
router ospf 1
daj
router ospf 0
Proces ospf można numerować od 1 w górę.
poniżej treść zadania, nie wiem czy to zgodne z regulaminem? więc jeżeli nie to proszę o usunięcie:
Use the following requirements to configure OSPFv2 routing on RA and RB:
- OSPFv2 routing requirements:
Process ID 1
Network address for each interface
Enable authentication for area 0
- OSPF priority set to 150 on the LAN interface of RA
- OSPF priority set to 100 on the LAN interface of RB
- OSPF MD5 authentication key ID of 1 and MD5 key “cisco” on the LAN interfaces of RA and RB
- Set the hello interval to 5
- Set the dead interval to 20
· Use the following requirements to configure RC OSPFv2 routing:
- OSPFv2 routing requirements:
Process ID 1
Network address for the LAN interface
Enable authentication for area 0
Set all interfaces to passive by default, allow OSPF updates on the active LAN
Set the router to distribute default routes
- Configure a directly attached default route to the Internet
- OSPF priority set to 50 on the LAN interface
- OSPF MD5 authentication key ID of 1 and MD5 key “cisco” on the LAN interface of RC
- Set the hello interval to 5
- Set the dead interval to 20
Note: Issue the clear ip ospf process command on RC if the default route does not propagate.
· Verify your configurations and test connectivity
- OSPF neighbors should be established and routing tables should be complete.
- RA should be the DR, RB should be the BDR.
- All three routers should be able to ping the web server.
po analizie Twojego configu wydaje mi się, że Packet Tracer nie zalicza Ci zadania, gdyż
zamiast rozgłaszać sieć , rozgłaszasz adres hosta.
Pod Router Ospf 1 zamiast
network 192.168.1.1 0.0.0.255 area 0
dla RA
powinno być :
network 192.168.1.0 0.0.0.255 area 0
-dla wszystkich routerów
Wtedy powinno Ci zaliczyć.
Pozdrawiam
wachu (przy okazji witam wszystkich)
po analizie Twojego configu wydaje mi się, że Packet Tracer nie zalicza Ci zadania, gdyż
zamiast rozgłaszać sieć , rozgłaszasz adres hosta.
Pod Router Ospf 1 zamiast
network 192.168.1.1 0.0.0.255 area 0
dla RA
powinno być :
network 192.168.1.0 0.0.0.255 area 0
-dla wszystkich routerów
Wtedy powinno Ci zaliczyć.
Pozdrawiam
wachu (przy okazji witam wszystkich)
Dzięki Wachu to było to. Efekt ten sam, ale teraz doczytałem, że faktycznie z punktu widzenia egzaminu nie jest to poprawne. Jeszcze raz dzięki wszystkim!